Tool Descriptions
Tool Descriptions
31 1 060 Fixture
(No Illustration)
Note: For testing wheel guide joints on front axle.
Series: E53
Order number: 31 1 060 Test Fixture
31 2 220 Support plate
Minimum set: Mechanical tools
In conjunction with: 00 2 030 (not included in minimum kit)
Note: For supporting front axle carrier when removing oil pan
Series: All
Engine: All
SI Number 1 06 94 (801)
Order number: 31 2 220 Support plate
31 2 260 Pressure Sleeve Tool
Minimum set: Mechanical tools
Series: E53
Storage location: A35
SI number 1 03 99 (418)
Order number: 31 2 260 Tool
Consisting of:
1 = 31 2 261 Pressure sleeve
4 = 31 2 264 Pressure sleeve
Note: For removal and installation purposes - Series: E53
31 3 340 Spring tensioner
Minimum set: Mechanical tools
Note: For tensioning coil springs when removing and installing spring strut. Used on front axle only.
Series: All models
Storage location: Single
SI Number 1 11 99 ($38)
Order number: 31 3 340 Spring tensioner
Consisting of:
1 = 31 3 341 Spring tensioner, single
2 = 31 3 342 Replacement pin
31 5 130 Set of impact drifts
Minimum set: Mechanical tools
In conjunction with: 00 5 500
Note: For fitting rotary shaft seals of output shafts at front axle differential
Series: E53
SI number: 1 15 99(483)
Order number: 31 5 130 Set of impact drifts
32 3 140 Setting tool
Minimum set: Mechanical tools
Note: For setting front camber
Series: E53
Order number: 32 3 140 Setting tool
Consisting of:
32 3 144 Screw
32 3 150 Setting tool
Minimum set: Mechanical tools
Note: For setting camber on rear axle
Series: E53
SI number: 1 15 99(483)
Order number: 32 3 150 Setting tool
Consisting of:
1 = 32 3 151 Extension piece
Note: For torque wrench
2 = 32 3 152 Socket tool WAF 18
32 3 160 T-handled socket wrench WAF 38
Minimum set: Mechanical tools
Note: For setting camber on front axle
Series: E53
SI number: 1 15 99(483)
Order number: 32 3 160 T-handled socket wrench WAF 38
32 4 000 Fixture
Note: For checking pump pressure in power steering system
Series: E53
Order number: 32 4 000 Fixture
Consisting of:
1 = 32 4 001 Pressure gauge 16 bar
2 = 32 4 002 Pressure gauge 160 bar
3 = 32 4 003 Testing fixture without pressure gauge
4 = 32 4 004 Lead wire
5 = 32 4 005 Connection piece
36 1 010 Spring lifter
Note: For lifting retaining spring when removing and installing balance weight
Series: E53
Storage location: A28
Order number: 36 1 010 Spring lifter
36 1 020 Tyre pliers
Note: For compressing sides of tyres when removing and installing retaining spring
Series: E53
Order number: 36 1 020 Tyre pliers
36 1 030 Tester
Note: For measuring vertical and lateral runout of wheels
Series: All models
SI number: 1 11 00(594)
Order number: 36 1 030 Tester
Consisting of:
1 = 36 1 031 Stand
2 = 36 1 032 Post with clamp
3 = 36 1 033 Holder with clamp
4 = 36 1 034 Clamp
5 = 36 1 035 Measuring roller
6 = 36 1 036 Dial gauge
36 1 040 Scraper
Note: For removing stick-on weights from aluminum rims
Series: All models
Storage location: Single
SI number: 1 13 00(596)
Order number: 36 1 040 Scraper
36 1 300 Set of wheel stud adapters
Minimum set: Mechanical tools
Note: For loosening and tightening wheel studs (antitheft)
Series: E53
Order number: 36 1 300 Set of wheel stud adapters
Consisting of:
36 1 301 Code 11
36 1 302 Code 12
36 1 303 Code 13
36 1 304 Code 14
36 1 306 Code 16
36 1 307 Code 17
36 1 308 Code 18
36 1 309 Code 19
36 1 311 Code 20
36 1 312 Code 31
36 1 313 Code 32
36 1 314 Code 33
36 1 315 Code 34
36 1 316 Code 35
36 1 317 Code 36
36 1 318 Code 37
36 1 319 Code 38
36 1 321 Code 39
36 1 322 Code 40
36 1 305 Code 15