Scan Tool Data Definitions

Scan Tool Data Definitions
Data Display/Definitions
The Scan Tool Data Display/Definitions contains a brief description of all the ABS/ TCS/VSES data parameters. The menus available depend on the number and type of system on the vehicle and are listed below in alphanumeric order.
^ ABS DATA
^ TCS DATA

ABS Active
The scan tool displays Yes or No. The scan tool will display Yes when the ABS is active and No during normal vehicle operation.

ABS Warning Lamp
The scan tool will display On or Off depending on the state of the ABS indicator.

Brake Switch
The scan tool will display Applied or Released depending on the state of the brake switch.

DRP Active
The scan tool will display Yes/No depending on the state of the DRP.

DRP Disabled
The scan tool will display Yes/No depending on the state of the DRP.

EBTCM to PCM Requested Torque
The scan tool displays 0-100 percent. The scan tool displays the duty cycle of the Delivered Torque PWM signal. The duty cycle of the signal is used to transmit how much torque the EBCM is requesting the PCM to deliver. Normal values are between 10 and 90 percent duty cycle. The signal should be at 90 percent duty cycle when traction control is not active and at a lower value, approximately 10 percent, when the traction control is active.

Engine Speed
The scan tool will display between 0 to 10200 RPM which is a digital tachometer display.

Ignition Voltage
The scan tool displays 0-17 Volts. The scan tool displays the level of ignition voltage at the EBCM.

LF Inlet Valve Solenoid
The scan tool will display Active or Inactive. The scan tool displays the commanded state of the LF inlet solenoid valve.

LF Outlet Valve Solenoid
The scan tool will display Active or Inactive. The scan tool displays the commanded state of the LF outlet solenoid valve.

LF TCS Isolation Solenoid
The scan tool will display Active/Inactive. This displays the commanded state of the solenoid valve.

LF TCS Prime Solenoid
The scan tool will display Active/Inactive. This displays the commanded of the solenoid valve.

Left Front Wheel Speed
The scan tool displays 0-255 km/h or (0-158 mph). The scan tool displays the actual speed of the left front wheel.

Left Rear Wheel Speed
The scan tool displays 0-255 km/h or (0-158 mph). The scan tool displays the actual speed of the left rear wheel.

Low Traction Lamp
The scan tool will display On/Off. This will indicate the state of the LOW TRAC Indicator.

LR Inlet Valve Solenoid
The scan tool displays Active or Inactive. The scan tool displays the commanded state of the LR inlet solenoid valve.

LR Outlet Valve Solenoid
The scan tool displays Active or Inactive. The scan tool displays the commanded state of the LR outlet solenoid valve.

Monitor Relay State
The scan tool display On /Off. This is the commanded state of the relay.

PCM to EBTCM Delivered Torque
The scan tool displays 0-100 percent. The scan tool displays the duty cycle of the Requested Torque PWM signal. The duty cycle of the signal is used to transmit how much engine torque the PCM is delivering. Normal values are between 10 and 90 percent duty cycle. The signal is at low values, approximately 10 percent, at idle and at higher values under driving conditions.

RF Inlet Valve Solenoid
The scan tool displays Active or Inactive. The scan tool displays the commanded state of the RF inlet solenoid valve.

RF Outlet Valve Solenoid
The scan tool displays Active or Inactive. The scan tool displays the commanded state of the RF outlet solenoid valve.

Right Front Wheel Speed
The scan tool displays 0-255 km/h or (0-158 mph). The scan tool displays the actual speed of the right front wheel.

RF TCS Isolation Solenoid
The scan tool will display Active/Inactive. This will be the commanded state of the solenoid valve.

RF TCS Prime Solenoid
The scan tool will display Active/Inactive. This will be the commanded state of the solenoid valve.

RR Inlet Valve Solenoid
The scan tool displays Active or Inactive - The scan tool displays the commanded state of the RR inlet solenoid valve.

RR Outlet Valve Solenoid
The scan tool displays Active or Inactive - The scan tool displays the commanded state of the RR outlet solenoid valve.

Right Rear Wheel Speed
The scan tool displays 0-255 km/h or (0-158 mph). The scan tool displays the actual speed of the right rear wheel.

Rough Road Parameters
The scan tool will display 0 to 1 g. The scan tool will display the EBCM calculation of the road surface roughness. This information is then sent to the PCM over the class 2 serial data line. This information is used by the PCM for misfire detection.

TCS Active
The scan tool displays Off or On. The scan tool displays On if the TCS indicator is currently being commanded ON.

TCS Switch State
The scan tool displays Pressed or Released. The scan tool will display the state of the Traction Control Switch.

TCS Warning Lamp
The scan tool will display On or Off depending on the state of the TCS indicator.

Valve Relay State
The scan tool will display On/Off depending on the state of the relay.