Campaign - Transmission And ECM Software Update
Subject:Customer Satisfaction - Transmission Software and Calibration Update
# 07274 - (11/02/2007)
Models:
2008 Buick Enclave
2007-08 GMC Acadia
2007-08 Saturn Outlook
2008 Saturn Aura
Condition
Certain 2007-08 model year GMC Acadia; Saturn Outlook; and 2008 model year Buick Enclave; Saturn Aura model vehicles were incorrectly reprogrammed by dealers/retailers in normal service and under Customer Satisfaction Program 07217A and Service Update 07235A. The TCM (Transmission Control Module) and ECM (Engine Control Module) both must be reprogrammed with the updated software for correct odometer operation. GM TIS2Web Service Programming System records indicate some vehicles have had only one of the modules reprogrammed, causing incorrect odometer function if the vehicle is driven. Attached to the Administrative Message (US) / Dealer Communication (Canada), used to release this bulletin, is a list, in BAC (US) / Dealer Code (Canada) sequence, of those vehicles which only had one module reprogrammed and which our records indicate are still in your inventory.
Correction
Dealers/Retailers are to reprogram the stock vehicles listed using the Programming Sequence procedure to assure that both the ECM and TCM have the updated software. Vehicles which have accumulated mileage with only one of the modules updated must be programmed using the Programming Sequence and must also have the vehicle odometer reading corrected using the service procedure detailed in this bulletin.
Vehicles Involved
IMPORTANT:
Dealers/retailers are to confirm vehicle eligibility prior to beginning repairs by using the system(s) below. Not all vehicles within the above breakpoints may be involved.
-- GM dealers and Canadian Saturn retailers should use GMVIS.
-- Saturn US retailers should use AS400 system.
For dealers/retailers with involved vehicles, a listing with involved vehicles containing the complete vehicle identification number, customer name, and address information has been prepared and will be provided through the applicable system listed below. Dealers/retailers will not have a report available if they have no involved vehicles currently assigned.
-- US GM - GM DealerWorld Recall Information
-- Canadian GM/Saturn dealers/retailers - GMinfoNet Recall Reports
-- US Saturn retailers - Facility VIN List (included with bulletin in GM DealerWorld)
-- Export dealers - sent directly to dealers
The listing may contain customer names and addresses obtained from Motor Vehicle Registration Records. The use of such motor vehicle registration data for any purpose other than follow-up necessary to complete this program is a violation of law in several states/provinces/countries. Accordingly, you are urged to limit the use of this report to the follow-up necessary to complete this program.
Parts Information
Do not attempt to order the calibration number from GMSPO. The calibration numbers required for this service procedure are programmed into control modules via a Techline Tech 2(R) scan tool and TIS 2 WEB website with the following calibration updates:
^ 2007 GMC Acadia and Saturn Outlook: Use data version 9.5 for 2007 or later, available on TIS 2 Web 09/16/07; and on TIS DVD version 10.0/2007 or later, mailed to dealers beginning 10/10/07.
^ 2008 GMC Acadia; Saturn Outlook, Aura ; and Buick Enclave: Use data version 8.5 for 2007 or later, available on TIS 2 Web 08/19/07; and on TIS DVD version 9.0/ 2007 or later, mailed to dealers beginning 09/12/07
If you cannot access the calibration, call the Techline Customer Support Center and it will be provided.
Service Procedure
If the vehicle has not been driven off the dealer lot since the original reprogram, it only requires the Programming Sequence procedure be performed, according to Bulletins 07217A or 07235A, to reprogram both TCM and ECM to assure correct odometer function. Customer vehicles and dealer stock vehicles, except Saturn Aura, which have accumulated mileage with only one module updated, must have the Programming Sequence performed and the odometer reading corrected. The Odometer Worksheet should be copied locally. The worksheet must be completed and the Techline Customer Support Center (TCSC) contacted for further instructions. A VCI will be provided to electronically correct the odometer reading using the Tech 2(R). The Saturn Aura odometer reading can not be corrected using this procedure. If a Saturn Aura in the retailer stock list has been delivered, or accumulated mileage prior to completion of the Programming Sequence, the VIN must be reported to TCSC for further handling.
Important:
When programming vehicles with the software update released in bulletins 07217A and 07235A, and for normal service, it is important that the engine and transmission modules both be updated. If both modules are not updated, odometer function will be affected. The Programming Sequence assures that both modules are updated.
Notice:
Before reprogramming, please check the battery condition to prevent a reprogramming error of any of the modules due to battery discharge. Battery voltage must be between 12 and 16 volts during reprogramming. If the vehicle battery is not fully charged use jumper cables from an additional battery. Be sure to turn off or disable any system that may put a load on the battery such as automatic headlamps, daytime running lights, interior lights, heating, ventilation and air conditioning (HVAC) system radio engine cooling fan, etc. A programming failure or control module damage may occur if battery voltage guidelines are not observed.
The ignition switch must be in the proper position. The Service Programming System (SPS) application prompts you to turn ON the ignition, with the engine OFF. DO NOT change the position of the ignition switch during the programming procedure, unless instructed to do so.
Make certain all tool connections are secure, including the following components and circuits:
^ The RS-232 communication cable port
^ The connection at the data link connector (DLC)
^ The voltage supply circuits
DO NOT disturb the tool harnesses while programming. If an interruption occurs during the programming procedure, programming failure or control module damage may occur.
DO NOT turn OFF the ignition if the programming procedure is interrupted or unsuccessful. Ensure that all control module and DLC connections are secure and the TIS terminal operating software is up to date.
1. Verify that there is a battery charge of 12 to 16 volts. The battery must be able to maintain a charge during programming. Use an additional jump battery if necessary. Only use approved Midtronics charger or Jumper Packs, etc. to maintain proper battery voltage during programming.
2. Reprogram the Engine Control Module (ECM) AND the Transmission Control Module (TCM).
IMPORTANT:
To ensure both controllers are programmed at the same time select Programming Sequence ECM/TCM on the Support Controller Screen (NOTE: This is the last selection in the scroll down box).
3. Vehicle Option select with RPO MH6 without RPO VPM.
4. DTCs may set during programming. Use the clear code function on the program complete screen to clear DTCs.
2007-08 Odometer Correction for Acadia, Outlook; and 2008 Enclave
IMPORTANT:
The "Programming Sequence ECM/TCM" procedure must be performed using the "Pass-Thru" method. You must first select one of the following methods in TIS2 WEB: J2534 Pass-Thru or Tech2(R) Legacy Pass-Thru Programming. DO NOT SELECT "tech2(R) Remote". This procedure can not be used on Saturn Aura. Contact TCSC with the VIN of a Saturn Aura requiring odometer correction for further handling.
1. J2534 Pass-Thru is the preferred method for the Programming Sequence ECM/TCM. Ensure both the ECM and TCM have been programmed with the latest software and calibration files.
2. Complete odometer worksheet and have it ready when calling the Customer Support Center (TCSC). Refer to the work sheet shown.
3. Using VCI number provided by TCSC, program instrument panel clusters (IPC).
4. Key ON and verify correct odometer value.
5. Key OFF.
6. Remove 10 amp Display fuse (1), wait at least 5 seconds, then re-install 10 amp display fuse.
6.1. Display fuse is located at I/P fuse block under the right side of instrument panel.
6.2. Remove instrument panel insulator/closeout panel push-pins.
6.3. Remove instrument panel insulator/closeout panel.
6.4. Install instrument panel insulator/closeout panel.
6.5. Install instrument panel insulator/closeout panel push-pins.
7. Key ON and verify correct odometer value.
8. Use Tech 2(R) to check for any IPC diagnostic trouble codes (DTC'S). If any DTCs are present, refer to Service Information (SI) for proper diagnostic procedures.
Clear any DTCs that may have set in the ECM and TCM after reprogramming both modules.
Courtesy Transportation
The General Motors Courtesy Transportation program is intended to minimize customer inconvenience when a vehicle requires a repair that is covered by the New Vehicle Limited Warranty. The availability of courtesy transportation to customers whose vehicles are within the warranty coverage period and involved in a product program is very important in maintaining customer satisfaction. Dealers are to ensure that these customers understand that shuttle service or some other form of courtesy transportation is available and will be provided at no charge. GM Dealers should refer to the General Motors Service Policies and Procedures Manual for Courtesy Transportation guidelines. Saturn US retailers should refer to GM messenger bulletins SAG20060292/SAG20060295 for Courtesy Transportation guidelines. Saturn Canada retailers should refer to applicable Home Office letter on this subject.
Claim Information - GM, Saturn Canada Only
Submit a Product Claim with the information shown.
Claim Information - Saturn US Only
1. To receive credit, submit a claim with the information shown.
Customer Notification - For US
General Motors will notify customers of this program on their vehicle by telephone from the Customer Assistance Outbound Call Center.
Customer Notification - For Canada
General Motors will notify customers of this program on their vehicle (a copy of customer letter will be provided in the near future).
Customer Notification - For Export
There are no Export owners within areas covered by the US National Traffic and Motor Vehicle Safety Act. For owners outside these areas, dealers should notify customers in accordance with information which will be provided by administrative message in the near future.
Dealer Program Responsibility - All
All unsold new vehicles in dealers' possession and subject to this program must be held and inspected/repaired per the service procedure of this program bulletin before customers take possession of these vehicles.
Dealers are to service all vehicles subject to this program at no charge to customers, regardless of mileage, age of vehicle, or ownership, from this time forward.
Customers who have recently purchased vehicles sold from your vehicle inventory, and for which there is no customer information indicated on the dealer listing, are to be contacted by the dealer. Arrangements are to be made to make the required correction according to the instructions contained in this bulletin. A copy of the customer letter is shown in this bulletin for your use in contacting customers. Program follow-up cards should not be used for this purpose, since the customer may not as yet have received the notification letter.
In summary, whenever a vehicle subject to this program enters your vehicle inventory, or is in your dealership for service in the future, you must take the steps necessary to be sure the program correction has been made before selling or releasing the vehicle.
Disclaimer