Replacement of Missing, Incorrect or Lost Parts
Lock key wrenches and/or I.D./Registration Cards are available from NI Industries.A. Lock key wrench missing upon delivery of vehicle from factory or lost after deliver:
Send I.D./Registration Card, along with a check in the amount of $7.50 made payable to NI Industries.
B. I.D./Registration Card missing:
Provide NI Industries with the lock bolt/nut color. A new color coordinated I.D./Registration Card will be forwarded to the dealership. A secondary identification method on the Electra, is the color coded lock key wrench cap; and a two letter color code on the lock key wrench (BK = black, etc.). Other series use a single code letter on the lock key wrench and color code on the lock bolt.
C. Lock key wrench does not fit lock bolt/nut. Send lock key wrench and I.D./Registration Card to NI Industries with a letter indicating the color of the lock bolt/nut in the center of the locking wire wheel cover. The proper lock key wrench and I.D./Registration Card will be returned to the dealership.
D. I.D./Registration Card and "T" shaped lock key wrench both missing.
Provide the color of the lock bolt/nut in the center of the wire wheel cover, along with a check in the amount of $7.50 made payable to NI Industries.
Part Ordering
All requests for lock key wrenches and I.D./Registration Cards must be made
on dealership stationary to:
NI Industries, Inc. Automotive Trim Division 39600 Orchard Hill Place Novi, Mi 48050
A, B, E, G, J & X MODELS WIRE WHEEL COVER INSTALLATION:
Other missing or incorrect part(s) such as locking wire wheel cover(s), lock bracket(s), medallion(s) and special lug nut(s) are available through GMWDD. See illustrations for parts identification.
LOCK ADAPTER OR
COVER CUP & BRACKET ANTI-ROTATION WHEEL
MODEL ASSY MEDALLION ASSY CLIPS NUT
A 25511220+ 25512648 22515623 (100 mm)*-JA1 1617075
22518787 (115 mm)* . JA2/JA3/JA8
B 25506534 25506530 25520262 10013779-JA1 22506314-JA1
22506315 JA3/JA5
C 25523352 25515955 25522565 25523353 1617075
E 25504652 25504363 1617759 1617075
G 25506533 25506531 25520262 1617075
X 25506532 25506531 25522221 1617075
J 25524318+ 25512648 22515701 1617075
* Bolt Circle + Includes medallion
CODE
LETTER COLOR A B,G,X E J C
A Red 14035631 22511949 25512649 14035631 1630024
B Green 14035642 22511950 25512650 14035632 1630025
C Brown 14035633 22511951 25512651 14035633
H Gold 14035634 22511952 25512652 14035634 1630027
L Black 14035635 22511953 25512653 14035635 1630028
Orange 1630029
Tan 1630030
Dark Brown 1630031
Silver 1630032
Gray 1630033
Blue 1630026
In addition to individual components, a complete lock wire wheel package (Option N91) is available through GMWDD for the 1985 models. Parts numbers for these packages are as follows:
PART
NUMBER MODEL
998568 Electra
997090 Riviera
997091 LeSabre (15" x 6" wheel) - JA1
997092 LeSabre (15" x 7" wheel) - JA3/JA5
997093 Regal
997094 Skylark
997788 Century (115 mm bolt circle) - JA1
998547 Century (110 mm bolt circle) - JA2/JA3/JA8
998697 Skyhawk (13" x 5.5" wheel)
When the vehicles is being made ready for delivery, the lock brackets are to be installed prior to installation of the wire wheel cover and medallions.
1. Raise vehicle with lift equipment.
2. Remove three (3) special lug nuts from each wheel for lock bracket installation - refer to illustrations.
3. Place lock bracket on lug nut studs.
4. Reinstall three (3) special lug nuts on each wheel to retain lock bracket and torque to specifications. LOOSE CONDITION OF LOCK BRACKET MAY BE NORMAL. WHEN LUG NUTS ARE SEATED, FRONT WHEEL STUDS WILL HAVE A RECESSED APPEARANCE, WHICH IS NORMAL
5. Install adapter or anti-rotation clips if required.
6. Install wheel cover on wheel.
NOTE: The Electra (C) models use a new lightweight center retention. wire cover. This cover relies on the center lock bracket and fastener to hold the cover on the wheel. It is important that installation instructions for the anti-rotation clips and cover are followed.
7. Tighten lock bolt/nut with lock key wrench.
8. Install center medallion.
9. Install removal instruction label as required.
10. The lock key wrench is to be placed in the glove box along with the I.D./Registration Card.