Doors - Hinge Replacements
9230buick02
Bulletin: 92-10-47
Date: June '92
Ref. No.: 92-213-10
Corp. Ref. No.: 231022R
SUBJECT:
DOOR HINGE REPLACEMENTS
(NEW POLICIES, PROCEDURES AND LABOR ALLOWANCES)
MODELS AFFECTED:
1989-1992 REGALS
APPLICATION: 1989 (after VIN K1448000) through 1992 Regals
New policies, procedures and labor time allowances have been developed regarding door hinge servicing on 1989 through 1992 Regal coupes and sedans.
POLICY:
If a single door hinge on any door at any location requires replacement, the second or remaining hinge must be replaced at the same time.
SERVICE PARTS
Service parts will be packaged in "door sets", or two hinges in each package. New part numbers are as follows:
PART NUMBER DESCRIPTION
10218445 Hinges, Right Front Door
10218446 Hinges, Left Front Door
10218447 Hinges, Right Rear Door
10218448 Hinges, Left Rear Door
Parts are currently available from GMSPO.
PROCEDURES
Notice:
This procedure differs from the previous procedure (Removing the door from the vehicle) in that:
a. The door remains on the vehicle.
b. Access to both front door hinges is made through the front wheelhouse area.
c. The hinges come pre-primed.
Notice:
In order to minimize door realignment, DO NOT remove both door hinges at the same time. Do each hinge separately, and replace any broken hinges first.
1. Place vehicle on hoist.
2. Using the proper lift points, raise vehicle to half-up position (until wheel/tire is chest high).
Notice:
Make sure that the doors are fully latched onto the lock striker and the doors are not locked.
3. Using two pieces of masking tape, place one piece to bridge the gap between the door and rocker panel and the second piece to bridge the gap between the door and quarter panel or rear door (to act as reference points for door alignment).
4. Cut the tape at the gap area using a utility knife or other suitable tool.
5. Remove the front tire and wheel assembly.
6. Starting at the top center of the front wheelhouse liner, remove all attaching screws located rearward of the top center of the liner.
7. Loosen the liner from the fender and position the liner forward of the front suspension assembly.
8. Remove the insulator cover attachments and insulator cover (located between fender and hinge pillar).
9. Clean the hinge mounting surfaces on the door and body with a rag and mark the hinge locations on the body surfaces with a grease pencil or other suitable marker.
10. Remove the hinge attaching fasteners and hinge from vehicle.
11. Install the new hinge within the previously marked locations using the new fasteners and lightly tighten the fasteners.
12. Repeat steps 10 and 11 for remaining hinge.
13. Install tire/wheel with 3 nuts and lower the vehicle to ground level.
14. Inspect the edges of the tape on the door and with the aid of a helper, align the door as necessary.
15. Raise the vehicle to the previous position and remove the tire/wheel assembly.
16. Tighten and torque the hinge attachments to:
Bolts - 46 N-m (34 Lbs.Ft.)
Nuts - 27 N-m (20 Lbs.Ft.)
17. Reinstall the insulator cover.
18. Reposition and install the wheelhouse liner using the original screws.
19. Reinstall the tire and wheel assembly.
20. Remove the reference tape from the door, rocker and quarter.
21. Lower hoist and remove the vehicle.
Procedure for replacement - Rear Doors -
Notice:
In order to minimize door realignwnt, DO NOT remove both door hinges at the same time. Do each hinge separately, and replace any broken hinges first.
1. Using two pieces of masking tape, place one piece to bridge the gap between the door and rocker panel and the second piece to bridge the gap between the door and quarter panel (to act as reference points for door alignment).
Cut the tape at the gap area using a utility knife or other suitable tool.
Notice:
Make sure that the doors are fully latched onto the lock striker and the doors are not locked.
3. With the front door open to access the center pillar and rear door hinge area, clean the hinge mounting surfaces on the door and body with a rag and mark the locations using a grease pencil or other suitable marker.
4. Remove the hinge attaching fasteners and hinge from vehicle.
5. Install the new hinge within previously marked locations and lightly tighten the fasteners.
6. Repeat steps 3 through 5 for the remaining hinge.
7. Inspect the edges of tape on the door and align the door as necessary.
8. Tighten and torque the hinge attachments to:
Bolts - 46 N-m (34 Lbs.Ft.)
Nuts - 27 N-m (20 Lbs.Ft.)
9. Remove the reference tape from the door, rocker and quarter.
WARRANTY INFORMATION:
Labor Operation: Time Allowance:
Front Doors
Both Right B4018 .9 Hrs.
Both Left B4019 .9 Hrs.
ADD:
- W/Locking Wheel Covers/Nuts (One Or All) .1 Hrs.
- To Color Coat .3 Hrs.
Material Allowance GB
Rear Doors:
Both Right B4418 .5 Hrs.
Both Left B4419 .5 Hrs.
ADD:
- To Color Coat .3 Hrs.
Material Allowance GB