Timing Chain, Sprockets, and Tensioner Installation
Tools RequiredJ 39579 Camshaft Sprocket Wrench
J 36008-A Camshaft Sprocket Alignment Pins
Important:
Ensure that the camshaft sprocket alignment pins are in the cylinder block and the timing chain housing, prior to installing the timing chain housing. The camshaft sprocket alignment pins ensure proper chain housing and front cover location for correct front oil-seal-to-crankshaft alignment.
1. Install J 36008-A through holes in the camshaft sprockets and into holes in the timing chain housing. This will position the camshaft for correct timing. See Figure 4.
2. Use the following steps if the camshafts are out of position and must be rotated more than 1/8 turn to install the alignment dowel pins:
Notice:
Failure to follow this procedure could result in severe engine damage.
a. The crankshaft must be rotated 90 clockwise off of TDC to give the valves adequate clearance to open.
b. Once the camshafts are in position and the J 36008-A Camshaft Sprocket Alignment Pins are installed, rotate the crankshaft counter-clockwise back to TDC.
Notice:
Do not rotate the crankshaft clockwise to TDC. Valve or piston damage could occur.
Important:
The timing chain and crankshaft sprocket must be put on in a specific direction for chain noise and wear considerations. The surfaces that were marked during removal should be showing when the chain and crankshaft sprocket are installed.
3. Install the timing chain over the exhaust camshaft sprocket around the coolant pump sprocket and around the crankshaft sprocket.
4. Remove the J 36008-A Camshaft Sprocket Alignment Pin from the intake camshaft. Use J 39579 in order to rotate the intake camshaft sprocket counter-clockwise enough to allow the timing chain to slide over the intake camshaft sprocket.
5. Release J 39579. The length of the chain between the two camshaft sprockets will tighten.
6. If properly timed, the J 36008-A Camshaft Sprocket Alignment Pin will slide in easily. If the dowel pin does not fully index, the camshafts are not timed correctly and the procedure must be repeated.
7. Leave the alignment dowel pins installed.
8. The keyway on the crankshaft and the mark on the cylinder block should be aligned, with the slack removed from the chain between the intake camshaft sprocket and the crankshaft sprocket. If the mark and the keyway are not aligned, move the chain one tooth forward or rearward; remove the slack and recheck the marks. See Figure 4.
9. Use the following steps in order to reload the tensioner assembly to its zero position:
a. Assemble the tensioner plunger and the tensioner body.
b. With the tensioner plunger fully extended, turn the tensioner and tensioner body upside down on a bench or other flat surface. A metal workbench is best for this.
c. With the plunger face against the workbench, press firmly on the bottom of the tensioner body, compress the tensioner plunger until it is seated flush in the tensioner. See Figure 5.
10. Install the tensioner body and plunger to the chain housing.
11. Install the timing chain tensioner shoe on the stud. Apply hand pressure to the timing chain tensioner shoe until the locking tab seats in the groove in the stud.
12. Tighten the timing chain tensioner body bolts. Do not over-tighten.
Tighten
Tighten the bolts to 10 N.m (89 lb in.) Refer to Fastener Notice in General Information.
13. Release the timing chain tensioner plunger.
Notice:
If the timing chain tensioner is not released from the installation position, engine damage will occur when the engine is started.
14. Using a flat-blade screwdriver, cotter pin remover, or a similar tool, press firmly against the face of timing chain tensioner plunger.
15. Depress the timing chain tensioner plunger until it is bottomed out in the bore of the timing chain tensioner. If the timing chain tensioner cannot be depressed, it is not properly loaded and the procedure for loading the timing chain tensioner must be repeated.
16. Release the tensioner plunger, the plunger will press firmly against the back of the timing chain tensioner shoe.
17. Remove J 36008-A from the camshaft sprockets. See Figure 6.
Notice:
The timing chain on the LD9 (VIN T) Twin Cam Engine is not to be replaced with the timing chain from any other model year. The timing sprockets are different on the Twin Cam engine and the shape of the links matches the sprockets. Engine damage may result if the wrong timing chain is used. The timing chain and the crankshaft sprocket must be marked so that they are reinstalled with the same side facing out at the time of reassembly.
18. Rotate the crankshaft clockwise two full rotations. Align the crankshaft keyway with the mark on the cylinder block and reinstall the J 36008-A Camshaft Sprocket Alignment Pins. The alignment pins will slide in easily if the engine is timed correctly.
19. Install the timing chain guides. See Figure 6.