Bearing & Housing Assembly

Part 1 Of 2:

Part 2 Of 2:

^ Tools Required:
- J 23653-SIR Lock Plate Compressor
- J 21854-01 Pivot Pin Remover

REMOVE OR DISCONNECT
1. Do all steps under REMOVE OR DISCONNECT in UPPER COVER LOWER COVER.
2. Do steps 1 through 7 under REMOVE OR DISCONNECT in UPPER HEAD HOUSING COMPONENTS.





3. Two tapping screws (30) from bottom of bearing & housing assembly (11).
4. Interlock solenoid assembly (29).
^ Let solenoid (29) hang freely.
5. Two tapping screws (26) from turn signal & multifunction switch assembly (32).
6. Turn signal & multifunction switch (32).
^ Remove pass key wire.
^ Let switch (32) hang freely.
7. Two tapping screws (23) from ignition & key alarm switch assembly (22).
8. Ignition switch (22).
^ Let ignition switch (22) hang freely.
9. Park lock cable assembly (47) from bottom of housing assembly (11).
A. Key in "RUN" position.
B. Push on locking tab on end of cable assembly (47) and remove.
10. Steering column lock cylinder set (15).
A. Turn lock cylinder (IS) to "RUN" position.
B. Push against locking button on back side of housing assembly (11) and remove lock cylinder (15).
C. Lock pre-load spring (13).
D. Pass key wire from securing position on housing assembly (11).
^ Let cylinder (15) hang freely.
11. Do all steps under REMOVE OR DISCONNECT in TILT WHEEL SPRING.
12. Shift lever to "PARK" position to gain access to pivot pins (53)
13. Two pivot pins (53) using J 21854-01.
14. Bearing & housing assembly (11).
^ Pull tilt arm to disengage steering wheel lock shoes from dowel pins in steering column jacket support assembly (54).

INSTALL OR CONNECT

NOTICE: Always use the correct fastener in the proper location. When you replace a fastener, use ONLY the exact part number for that application. The manufacturer will call out those fasteners that require a replacement after removal. The manufacturer will also call out the fasteners that require thread lockers or thread sealant. UNLESS OTHERWISE SPECIFIED, do not use supplemental coatings (paints, greases, or other corrosion inhibitors) on threaded fasteners or fastener joint interfaces. Generally, such coatings adversely affect the fastener torque and joint clamping force, and may damage the fastener. When you install fasteners, use the correct tightening sequence and specifications. Following these instructions can help you avoid damage to parts and systems. Failure to do so may result in component damage or malfunction of steering column.

1. Bearing & housing assembly (11).
^ Using tilt lever position lock shoes to dowel pins.
^ Rotate housing assembly (11) until holes for pivot pins (53) line up.
2. Two pivot pins (53).
A. Shift lever to "PARK" position.
B. Lubricate with lithium grease.
C. Press pins.until firmly seated two places.
D. Stake pins (53) three locations two places.
3. Do all steps under INSTALL OR CONNECT in TILT WHEEL SPRING.
4. Steering column lock cylinder set (15).
A. Lock pre-load spring (13) to housing assembly (11).
B. Key installed in lock cylinder (15).
C. Ensure sector is in "RUN" position.
D. Line up locking tab with slot in housing assembly (11) and push into position.
E. Pass key wire to securing position on housing assembly (11).
5. Park lock cable (47) to bottom of housing assembly (11).
^ Do step 4 and Adjust under INSTALL OR CONNECT in PARK LOCK CABLE ASSEMBLY.
6. Ignition & key alarm switch (22) to housing assembly (11).
7. Two tapping screws (23) to ignition switch (22).

Tighten
Tighten screws (23) to 1.5 Nm (13 lb in).

8. Turn signal & multifunction switch (32) to housing assembly (11).
9. Two tapping screws (26) to multifunction switch (32).

Tighten
Tighten screws (26) to 5 Nm (44 lb in).

10. Secure pass key wire to multifunction switch (32).
11. Interlock solenoid assembly (29) to bottom of housing assembly (11).
12. Two tapping screws (30) to interlock solenoid (29).

Tighten
Tighten screws (30) to 2 Nm (18 lb in).

13. Do steps 2 through 8 under INSTALL OR CONNECT in UPPER HEAD HOUSING COMPONENTS.
14. Do all steps under INSTALL OR CONNECT in UPPER COVER LOWER COVER.