Operation CHARM: Car repair manuals for everyone.

P0101

Diagnostic Chart (Part 1 Of 2):




Diagnostic Chart (Part 2 Of 2):




Schematic:




CIRCUIT DESCRIPTION
The Mass Air Flow (MAF) sensor measures the amount of air which passes through it into the engine during a given time. The Powertrain Control Module (PCM) uses the mass air flow information to monitor engine operating conditions for fuel delivery calculations. A large quantity of air entering the engine indicates an acceleration or high load situation while a small quantity of air indicates deceleration or idle. The MAF sensor produces a frequency signal which can be monitored using a scan tool. The frequency will vary within a range of around 2000 Hertz at idle to about 10,000 Hertz at maximum engine load. If the signal from the MAF sensor does not match a predicted value based on barometric pressure, calculated from MAP at key ON, throttle position, and engine RPM, DTC P0101 will set.

CONDITIONS FOR RUNNING THE DTC
^ The engine is running.
^ System voltage is between 916 volts.
^ The throttle is steady and TP angle is below 50 percent.
^ EGR duty cycle is below 50 percent.
^ EGR pintle position is below 50 percent.

CONDITIONS FOR SETTING THE DTC
^ MAF signal frequency indicates an airflow significantly higher or lower than a predicted value based on barometric pressure, throttle position and engine RPM.
^ The above conditions are present for at least 12 seconds.

ACTION TAKEN WHEN THE DTC SETS
^ The PCM will illuminate the Malfunction Indicator Lamp (MIL) during the second consecutive trip in which the diagnostic has been run and failed.
^ If equipped with traction control, the PCM will command the Electronic Brake And Traction Control Module (EBTCM) via the serial data circuit to turn OFF traction control, and the EBTCM will illuminate the TRACTION OFF lamp.
^ The PCM will store conditions which were present when the DTC set as Freeze Frame and Failure Records data.

CONDITIONS FOR CLEARING THE MIL/DTC
^ The PCM will turn OFF the MIL during the third consecutive trip in which the diagnostic has been run and passed.
^ The History DTC will clear after 40 consecutive warm-up cycles have occurred without a malfunction.
^ The DTC can be cleared by using a scan tool.

DIAGNOSTIC AIDS
Inspect for the following conditions:
^ Skewed or stuck TP sensor - A malfunctioning TP sensor or TP sensor circuit can cause the PCM to incorrectly calculate the predicted Mass Air Flow value. Observe the Throttle Angle displayed on a scan tool with the throttle closed. If the Throttle Angle reading is not 0 percent, inspect and test for the following conditions and repair as necessary:
- Throttle plate sticking or excessive deposits on the throttle plate or in the throttle bore.
- TP sensor signal circuit shorted to voltage.
- Poor connection or high resistance in the TP sensor ground circuit.
- If none of the above conditions are noted and the Throttle Angle reading at Closed Throttle is not 0 percent, replace the TP sensor.
^ Misrouted harness - Inspect the MAF sensor harness to ensure that it is not routed too close to high voltage wires such as spark plug leads.
^ Plugged intake air duct or dirty air filter element - A Wide Open Throttle acceleration from a stop should cause the Mass Air Flow displayed on a scan tool to increase from about 4-7 gm/s at idle to 100 gm/s or more at the time of the 1-2 shift. If not, check for a restriction.
^ Skewed or unresponsive MAP sensor - The barometric pressure used to calculate the default Mass Air Flow value is based on the MAP sensor reading. A skewed MAP sensor at key ON will cause the BARO reading to be incorrectly calculated. Also, with the engine running, an unresponsive MAP sensor, due to poor vacuum connections, damaged vacuum source, defective vacuum hoses, or unmetered air into the manifold, will cause inaccurate BARO reading updates during Wide Open Throttle conditions. Both of these conditions result in a difference between the actual MAF sensor signal and the predicted MAF value, PCM calculated. If a large difference between these two values occurs DTC P0101 will set. This condition may also cause abnormal IAC counts. With the IAC at an incorrect count value, a hard start/no start condition may occur.

IMPORTANT: Remove any debris from the connector surfaces before servicing a component. Inspect the connector gaskets when diagnosing or replacing a component. Ensure that the gaskets are installed correctly. The gaskets prevent contaminate intrusion.

^ Poor terminal connection-Inspect the harness connectors for backed out terminals, improper mating, broken locks, improperly formed or damaged terminals, and faulty terminal to wire connection. Use a corresponding mating terminal to test for proper tension.
^ Damaged harness-Inspect the wiring harness for damage. If the harness inspection does not reveal a problem, observe the display on the scan tool while moving connectors and wiring harnesses related to the sensor. A change in the scan tool display may indicate the location of the fault.
^ PCM and engine grounds for clean and secure connections

If the DTC is determined to be intermittent, reviewing the Failure Records can be useful in determining when the DTC was last set.

TEST DESCRIPTION
The numbers below refer to the step numbers on the diagnostic table.
3. Only if sent here from the Engine Cranks But Does Not Run, continue to follow the diagnostic table even if DTC P0101 has NOT failed this ignition.
4. This step checks the MAP sensor. By disconnecting the MAF sensor, the vehicle is forced into speed density. Speed density is based on the MAP, TP, and engine RPM readings. With a skewed/unresponsive MAP sensor, the speed density calculation is incorrect and the vehicle may not start. For further information refer to Diagnostic Aids.
5. This step checks for a skewed or sticking MAP sensor. The MAP sensor should respond smoothly and gradually as RPM is increased. Compare the MAP sensor of the affected vehicle to that of a normally operating vehicle. If a large difference is noted, replace the MAP sensor.
9. This step verifies that ignition feed voltage and a good ground are available at the MAF sensor.