Scan Tool Data Definitions
Airbag Warning Lamp: The scan tool displays On/Off. The state of the air bag indicator as commanded by the IPC.Analog Dim: The scan tool displays 0.1 to 13.6 V. The IPC uses the instrument panel dimming control circuit to determine the intensity of the electronic displays in the IPC.
Antilock Lamp: The scan tool displays On/Off. The state of the ABS indicator as commanded by the IPC.
Brake Warning Lamp: The scan tool displays On/Off. The state of the brake system indicator as commanded by the IPC.
Change Oil Lamp: The scan tool displays On/Off. The state of the CHANGE OIL SOON indicator as commanded by the IPC.
Cluster Part Number: The scan tool displays the 4 digit part number of the IPC.
Coolant Hot Lamp: The scan tool displays On/Off. The state of the engine coolant temperature indicator as commanded by the IPC.
Crank: The scan tool displays Active/Inactive. The IPC displays Active if it senses voltage at the crank voltage circuit.
Cruise Lamp: The scan tool displays On/Off. The state of the CRUISE indicator as commanded by the IPC.
Driver Door Switch: The scan tool displays Open/Closed. The BCM monitors the driver door ajar switch, where a closed switch is displayed as Open.
Door Ajar Lamp: The scan tool displays On/Off. The state of the DOOR/TRUNK indicator as commanded by the IPC.
ECT Sensor: The scan tool displays -40-151 °C (-40-304 °F). The PCM monitors the voltage at the signal circuit of the engine coolant temperature sensor. The voltage is inversely proportional to the engine coolant temperature.
Engine Oil Level Switch: The scan tool displays Ok/Low. The PCM monitors the signal circuit of the engine oil level switch, where an open switch is displayed as Low (low engine oil level).
Engine Oil Life Remaining: The scan tool displays 0 - 100%. The PCM calculates the remaining engine oil life.
Engine Oil Pressure Switch: The scan tool displays Ok/Low. The PCM monitors the signal circuit of the engine oil pressure switch, where an open switch is displayed as Low (low engine oil pressure).
Engine Speed: The scan tool displays 0-9999 RPM. Engine speed is computed by the PCM from the 3X reference input. It should remain close to desired idle under various engine loads with he engine idling.
English/Metric State: The scan tool displays English Units/Metric. The units are changed via the driver information center (DIC).
FEIC MODE: The scan tool displays On/Off. The state of the fuel efficiency information center (FEIC) mode switch. The scan tool displays On when the switch is depressed.
FEIC RESET: The scan tool displays On/Off. The state of the fuel efficiency information center (FEIC) reset switch. The scan tool displays On when the switch is depressed.
Fuel Level: The scan tool displays 0 - 100 %. The PCM calculates the amount of fuel remaining in the tank based on the input from the fuel level sensor. The IPC receives a class 2 message from the PCM indicating the fuel level percent.
Fuel Level Sensor: The scan tool displays 0-5 volts. The PCM monitors the signal circuit of the fuel level sensor.
Ignition 0: The scan tool displays Active/Inactive. The IPC displays Active if it senses voltage at the ignition 0 voltage circuit.
Ignition 0: The scan tool displays 0-16 volts. The voltage measured from the ignition 0 voltage circuit of the IPC.
Ignition 1: The scan tool displays Active/Inactive. The IPC displays Active if it senses voltage at the ignition 1 voltage circuit.
Julian Date of Build: The scan tool displays the 4 digit build date of the IPC.
Key In Ignition: The scan tool displays Yes/No. The BCM monitors the ignition key alarm switch, where a closed switch is displayed as Yes (key is in the ignition).
LCM Lights On Chime: The scan tool displays On/Off. The BCM monitors the headlamp switch, where an open switch is displayed as On (headlamp switch is in the off position).
Left Turn Signal: The scan tool displays Active/Inactive. The IPC monitors the left turn signal switch, where a closed switch is displayed as Active.
Location of Manufacture: The scan tool displays Metramoros/Flint/Delnosa. The scan tool displays the manufacture location of the IPC.
Low Coolant Input: The scan tool displays Active/Inactive. The IPC monitors the engine coolant indicator module, where a closed switch is displayed as Active (low coolant level).
Low Coolant Lamp: The scan tool displays On/Off. The state of the low engine coolant level indicator as commanded by the IPC.
Low Fuel Lamp: The scan tool displays On/Off. The state of the low fuel indicator as commanded by the IPC.
Low Oil Lamp: The scan tool displays On/Off. The state of the low engine oil level indicator as commanded by the IPC.
Low Tire Lamp: The scan tool displays On/Off. The state of the low tire indicator as commanded by the IPC.
Low Trac Lamp: The scan tool displays On/Off. The state of the LOW TRAC indicator as commanded by the IPC.
Low Wash Input: The scan tool displays Active/Inactive. The IPC monitors the windshield washer solvent level switch, where a closed switch is displayed as Active (low washer fluid).
Low Washer Lamp: The scan tool displays On/Off. The state of the LOW WASH indicator as commanded by the IPC.
Oil Pressure Lamp: The scan tool displays On/Off. The state of the engine oil pressure indicator as commanded by the IPC.
Park Brake Switch: The scan tool displays On/Off. The BCM monitors the park brake switch, where a closed switch is displayed as On.
Park Lamp: The scan tool displays Active/Inactive. The IPC monitors the headlamp switch, where a closed switch is displayed as Active (headlamp switch is in the park or head position).
PROM ID: The scan tool displays a 4 digit number that the identifies the PROM.
Right Turn Signal: The scan tool displays Active/Inactive. The IPC monitors the right turn signal switch, where a closed switch is displayed as Active.
Seat Belt Lamp: The scan tool displays On/Off. The state of the fasten safety belt indicator as commanded by the IPC.
Security Lamp: The scan tool displays On/Off. The state of the SECURITY indicator as commanded by the IPC.
Service Vehicle Soon Lamp: The scan tool displays On/Off. The state of the SERVICE VEHICLE SOON indicator as commanded by the IPC.
Software Release, Day: The scan tool displays the 2 digit number which corresponds to the day of the IPC software release.
Software Release, Month: The scan tool displays the 2 digit number which corresponds to the month of the IPC software release.
Software Release, Year: The scan tool displays the 2 digit number which corresponds to the year of the IPC software release.
Software Version: The scan tool displays the 2 digit number software version of the IPC.
Traction off Lamp: The scan tool displays On/Off. The state of the TRAC OFF indicator as commanded by the IPC.
Vehicle Speed: The scan tool displays 0-100 mph. The IPC receives a class 2 message from the PCM indicating the vehicle speed.
Vehicle Speed Sensor: The scan tool displays 0-255 km/h (0-155 mph). The PCM monitors the voltage at the signal circuit of the vehicle speed sensor. The voltage is proportional to the vehicle speed.
Volt Lamp: The scan tool displays On/Off. The state of the charging system indicator as commanded by the IPC.