Operation CHARM: Car repair manuals for everyone.

P0135

CIRCUIT DESCRIPTION
Heated oxygen sensors (HO2S) are used for fuel control and post catalyst monitoring. Each HO2S compares the oxygen content of the surrounding air with the oxygen content of the exhaust stream. When the vehicle is first started the powertrain control module (PCM) operates in an Open Loop mode, ignoring the HO2S signal voltage when calculating the air-to-fuel ratio. The PCM supplies the HO2S with a reference, or bias, voltage of about 450 mV. The HO2S generates a voltage within a range of 0-1,000 mV that fluctuates above and below bias voltage once in Closed Loop. A high HO2S voltage output indicates a rich fuel mixture. A low HO2S voltage output indicates a lean mixture. Heating elements inside the HO2S minimize the time required for the sensors to reach operating temperature, and to provide an accurate voltage signal. The PCM controls the HO2S 1 heater low control circuit with a low side driver. The HO2S 1 heater diagnostic monitors the current draw through the HO2S 1 low side driver when the engine is running. This DTC will set if the current level is not within the calibrated range.

Each HO2S 1 has the following circuits:
^ HO2S 1 high signal
^ HO2S 1 low reference
^ HO2S 1 heater ignition voltage HO2S 1 heater low control
^ Low reference loop

CONDITIONS FOR RUNNING THE DTC
^ DTCs P0101, P0102, P0103, P0107, P0108, P0112, P0113, P0116, P0117, P0118, P0121, P0122, P0123, P0125, P0128, P0201, P0202, P0203, P0204, P0205, P0206, P0410, P0440, P0442, P0443, P0446, P0449, or P1441 are not set.
^ The system voltage is between 9-18 volts.
^ The engine has been running for at least 4 minutes.
^ The engine coolant temperature (ECT) is more than 70°C (158°F).
^ The engine speed is between 650-2,500 RPM.
^ The mass air flow (MAF) is between 4-26 g/s.

CONDITIONS FOR SETTING THE DTC
The HO2S 1 heater current is not within the calibrated range.

ACTION TAKEN WHEN THE DTC SETS
The PCM illuminates the malfunction indicator lamp (MIL) on the second consecutive ignition cycle that the diagnostic runs and fails.

The PCM records the operating conditions at the time the diagnostic fails. The first time the diagnostic fails, the PCM stores this information in the Failure Records. If the diagnostic reports a failure on the second consecutive ignition cycle, the PCM records the operating conditions at the time of the failure. The PCM writes the operating conditions to the Freeze Frame and updates the Failure Records.

CONDITIONS FOR CLEARING THE DTC
^ The PCM turns OFF the MIL after 3 consecutive ignition cycles that the diagnostic runs and passes.
^ A current, DTC last test fails, clears when the diagnostic runs and passes.
^ A DTC stored in history clears after 40 warm-up cycles, if no failures are reported by this or any other emission related diagnostic.
^ A scan tool can be used to clear the DTC.

TEST DESCRIPTION

Steps 1-9:




Steps 10-19:




The numbers below refer to the step numbers on the diagnostic table.
2. Inspect the heater current with the engine at operating temperature, and allow time for the heater current to stabilize. The HO2S 1 heater current is initially higher until the sensor reaches full operating temperature.
4. This step ensures that the ignition voltage circuit to the HO2S 1 is not open or shorted. The test lamp should be connected to a good chassis ground, in case the HO2S 1 low reference or HO2S 1 heater low control circuit is malfunctioning.
6. This step inspects the HO2S 1 heater ground circuit. The engine must be running for the PCM to enable the heater low control driver to provide a path to ground.