B1475
DTC B1475
Diagnostic Instructions
* Perform the Diagnostic System Check - Vehicle (Initial Inspection and Diagnostic Overview) prior to using this diagnostic procedure.
* Review Strategy Based Diagnosis (Initial Inspection and Diagnostic Overview) for an overview of the diagnostic approach.
* Diagnostic Procedure Instructions (Initial Inspection and Diagnostic Overview) provides an overview of each diagnostic category.
DTC Descriptor
DTC B1475
- Retained Accessory Power Circuit
Diagnostic Fault Information
Circuit Description
The body control module (BCM) controls various accessories through the retained accessory power (RAP) relay circuit. When the ignition switch is in either the ACC or the ON position, the BCM grounds the RAP relay control circuit, energizing the RAP relay. When the RAP relay is energized, it supplies a B+ to the various accessories.
When the ignition switch turns from ON or ACC to OFF, with all of the vehicle doors closed, the BCM keeps the relay energized for 10 minutes, or until any vehicle door opens.
Conditions for Running the DTC
The system voltage must be between 9-16 volts.
Conditions for Setting the DTC
* The BCM detects a short to voltage in the RAP relay control circuit when the BCM is trying to energize the relay.
* The BCM detects that the RAP relay control circuit is open.
* The condition above must be present for more than 1 second.
Action Taken When the DTC Sets
* The BCM stores DTC B1475 in memory.
* The devices powered by the RAP relay will not operate.
Conditions for Clearing the DTC
* A current DTC clears when the malfunction is no longer present.
* A history DTC clears when the module ignition cycle counter reaches the reset threshold, without a repeat of the malfunction.
Reference Information
Schematic Reference
Power Distribution Schematics (Power Distribution Diagrams)
Connector End View Reference
Component Connector End Views (Connector Views)
Description and Operation
Retained Accessory Power Description and Operation (Retained Accessory Power Description and Operation)
Electrical Information Reference
* Circuit Testing (Component Tests and General Diagnostics)
* Connector Repairs (Component Tests and General Diagnostics)
* Testing for Intermittent Conditions and Poor Connections (Component Tests and General Diagnostics)
* Wiring Repairs (Component Tests and General Diagnostics)
Scan Tool Reference
Control Module References (Programming and Relearning) for Scan Tool Information
Circuit/System Verification
Ignition ON, command the retained accessory power (RAP relay) ON and OFF with a scan tool. Feel/listen for the operation of the RAP relay.
Circuit/System Testing
1. Ignition OFF, disconnect the RAP relay.
2. Test for less than 5 Ohms between the ground circuit terminal N1 and ground.
• If greater than the specified range, test the ground circuit for an open/high resistance.
3. Connect a test lamp between the relay control circuit terminal M3 and ground.
4. Cycle the ignition ON and OFF. The test lamp should turn ON and OFF when changing ignition switch positions.
• If the test lamp is always ON, test the control circuit for a short to voltage. If the circuit tests normal, replace the BCM.
• If the test lamp is always OFF, test the control circuit for a short to ground or open/high resistance. If the circuit tests normal, replace the BCM.
5. If all circuits test normal, test or replace the RAP relay.
Component Testing
1. Ignition OFF, disconnect the RAP relay.
2. Test for 70 - 150 Ohms between the B+ terminal 85 and the ground terminal 86 of the relay.
• If not within the specified range, replace the relay.
3. Test for infinite resistance between the following terminals:
* 30 and 86
* 30 and 87
* 30 and 85
* 85 and 87
• If not the specified value, replace the relay.
4. Install a 3 A fused jumper wire between relay terminal 85 and 12 V. Install a jumper wire between relay terminal 86 and ground. Test for less than 2 Ohms between terminals 30 and 87.
• If greater than the specified range, replace the relay.
Repair Instructions
Perform the Diagnostic Repair Verification (Verification Tests) after completing the diagnostic procedure.
* Relay Replacement (Attached to Wire Harness) (Relay Replacement (Attached to Wire Harness))Relay Replacement (Within an Electrical Center) (Relay Replacement (Within an Electrical Center))
* Control Module References (Programming and Relearning) for BCM replacement, setup, and programming