Drivetrain and Front Suspension Frame Replacement (3.9L)
Drivetrain and Front Suspension Frame Replacement (3.9L)
Special Tools
J 39580 Engine Support Stand
Removal Procedure
1.Install the engine support fixture. Refer to Engine Support Fixture .
2.Raise the vehicle on a hoist. Refer to Lifting and Jacking the Vehicle .
3.Remove the tire and wheel assemblies. Refer to Tire and Wheel Removal and Installation .
4.Remove the front air deflector. Refer to Front Air Deflector Replacement Front Air Deflector Replacement .
5.Disconnect the antilock brake system (ABS) sensor from the wheel speed sensor and frame.
6.Disconnect the lower ball joints from the steering knuckles. Refer to Lower Control Arm Replacement .
7.Remove the tie rod ends from the steering knuckles. Refer to Steering Linkage Outer Tie Rod Replacement .
8.Remove both stabilizer links from the stabilizer bar.
9.Remove the power steering gear mounting bolts and secure the gear out of the way using mechanics wire or equivalent, being sure not to overextend the intermediate shaft. Refer to Steering Gear Replacement .
10.Remove the engine mount nuts from the frame. Refer to Engine Front Mount Replacement and Engine Rear Mount Replacement .
11.Remove the rear transmission mount bolt from the frame. Refer to Transmission Rear Mount Replacement .
12.Remove the left transmission mount nuts from the frame. Refer to Transmission Mount Replacement - Left Side .
13.Remove the rear transmission mount bracket nuts from the frame. Refer to Transmission Rear Mount Bracket Replacement
14.Remove the brake lines from the retainers on the frame.
15.Lower the vehicle until the frame contacts the J 39580 .
16.Remove the reinforcement bolts (1).
17.Remove the front frame bolts (1).
18.Remove the rear frame bolts (4).
19.Remove the frame reinforcements (3).
20.Raise the vehicle off of the frame.
21.Remove the following components if replacing the frame:
-The lower control arms - Refer to Lower Control Arm Replacement .
-
-The stabilizer shaft - Refer to Stabilizer Shaft Replacement .
-
Installation Procedure
1.Install the following components on the suspension crossmember if removed:
-The stabilizer shaft - Refer to Stabilizer Shaft Replacement .
-The lower control arms - Refer to Lower Control Arm Replacement .
2.Lower the vehicle on to the frame.
3.Install the frame reinforcements (3).
Caution:Refer to Fastener Caution .
4.Install the rear frame bolts (4) and tighten to100 N �m (74 lb ft) plus 90 degree rotation.
5.Install the front frame bolts (1) and tighten to100 N �m (74 lb ft) plus 90 degree rotation.
6.Install the cradle support bolts (1) and tighten to100 N �m (74 lb ft).
7.Raise the vehicle.
8.Install the brake lines to the retainers on the frame.
9.Install the rear transmission mount bracket nuts. Refer to Transmission Rear Mount Bracket Replacement
10.Install the left transmission mount nuts to the frame. Refer to Transmission Mount Replacement - Left Side
11.Install the rear transmission mount bracket bolt. Refer to Transmission Rear Mount Replacement
12.Install the engine mount nuts to the frame. Refer to Engine Front Mount Replacement and Engine Rear Mount Replacement
13.Install the power steering gear mounting bolts. Refer to Steering Gear Replacement .
14.Install both stabilizer links to the stabilizer bar and tighten the nut to65 N �m (48 lb ft) plus 180 degree rotation.
15.Install the tie rod ends to the steering knuckles. Refer to Steering Linkage Outer Tie Rod Replacement .
16.Install the lower ball joints to the steering knuckles.
-Tighten the ball stud to steering knuckle pinch nut to50 N �m (37 lb ft).
-Reverse the nut � of a turn.
-Tighten to50 N �m (37 lb ft) plus 60 degrees.
17.Connect the ABS sensor to the wheel speed sensor and frame.
18.Install the front air deflector. Refer to Front Air Deflector Replacement Front Air Deflector Replacement .
19.Install the tire and wheel assemblies. Refer to Tire and Wheel Removal and Installation .
20.Remove the engine support fixture.
21.Bleed the power steering system. Refer to Power Steering System Bleeding .