Daytime Running Lamps Malfunction
Daytime Running Lamps Malfunction
Diagnostic Instructions
* Perform the Diagnostic System Check - Vehicle (Diagnostic System Check - Vehicle) prior to using this diagnostic procedure.
* Review Strategy Based Diagnosis (Strategy Based Diagnosis) for an overview of the diagnostic approach.
* Diagnostic Procedure Instructions (Diagnostic Procedure Instructions) provides an overview of each diagnostic category.
Diagnostic Fault Information
Circuit/System Description
The ambient light sensor is a light sensitive transistor that varies the voltage signal to the body control module (BCM) based on outside lighting conditions. When the ambient light sensor indicates daytime conditions with engine running, the body control module (BCM) grounds the DRL relay control circuit, energizing the DRL relay. With the DRL relay energized, voltage is applied through the relay switch contacts, the DRL 1 fuse, and the DRL 2 fuse to the left and right low beam headlamps. Any function or condition that turns the headlamps ON will cancel DRL operation.
Reference Information
Schematic Reference
Headlights/Daytime Running Lights (DRL) Schematics (Headlights/Daytime Running Lights (DRL) Schematics)
Connector End View Reference
Component Connector End Views (Connector Views)
Description and Operation
Exterior Lighting Systems Description and Operation (Exterior Lighting Systems Description and Operation)
Electrical Information Reference
* Circuit Testing (Circuit Testing)
* Connector Repairs (Connector Repairs)
* Testing for Intermittent Conditions and Poor Connections (Testing for Intermittent Conditions and Poor Connections)
* Wiring Repairs (Wiring Repairs)
Scan Tool Reference
Control Module References (Programming and Relearning) for scan tool information
Circuit/System Testing
1. Ignition OFF, disconnect the DRL relay.
2. Ignition ON, headlamps OFF, verify that a test lamp does not illuminate between the control circuit terminal 94 and ground.
• If the test lamp illuminates, test the control circuit for a short to voltage.
3. Verify that a test lamp illuminates between the B+ circuit terminal 90 and ground.
• If the test lamp does not illuminate, test the B+ circuit for a short to ground or an open/high resistance.
4. Verify that a test lamp illuminates between the B+ circuit terminal 93 and ground.
• If the test lamp does not illuminate, test the B+ circuit for an open/high resistance.
5. Connect a test lamp between the B+ circuit terminal 90 and the control circuit terminal 92.
6. Command the DRL ON and OFF with a scan tool. The test lamp should turn ON and OFF when changing between the commanded states.
• If the test lamp is always ON, test the control circuit for a short to ground. If the circuit tests normal, replace the BCM.
• If the test lamp is always OFF, test the control circuit for a short to voltage or an open/high resistance. If the circuit tests normal, replace the BCM.
7. Headlamps OFF, connect a 3A fused jumper wire between the B+ circuit terminal 93 and the control circuit terminal 92. The low beam headlamps should illuminate.
• If the low beam headlamps do not illuminate, test the control circuit for an open/high resistance. If the circuit tests normal, replace the rear fuse block.
8. If all circuits test normal, test or replace the DRL relay.
Component Test
Relay Test
1. Ignition OFF, disconnect the DRL relay.
2. Test for 70-100 ohms of resistance between terminals 85 and 86.
• If the resistance is not within the specified range, replace the relay.
3. Test for infinite resistance between the following terminals:
* 30 and 85
* 30 and 86
* 30 and 87
* 85 and 87
• If not the specified value, replace the relay.
4. Install a 10A fused jumper wire between relay terminal 85 and B+. Install a jumper wire between relay terminal 86 and ground. Test for less than 2 ohms of resistance between terminals 30 and 87.
• If greater than the specified range, replace the relay.
Repair Instructions
Perform the Diagnostic Repair Verification (Verification Tests) after completing the diagnostic procedure.
* Underhood Electrical Center or Junction Block Replacement (Removal and Replacement).
* Control Module References (Programming and Relearning) for BCM replacement, setup, and programming