B2575
DTC B2575 or B2699
Diagnostic Instructions
* Perform the Diagnostic System Check - Vehicle Diagnostic System Check - Vehicle prior to using this diagnostic procedure.
* Review Strategy Based Diagnosis Strategy Based Diagnosis for an overview of the diagnostic approach.
* Diagnostic Procedure Instructions Diagnostic Procedure Instructions provides an overview of each diagnostic category.
DTC Descriptors
DTC B2575 02
-
Headlamps Control Circuit Short to Ground
DTC B2575 04
-
Headlamps Control Circuit Open
DTC B2699 02
-
Right Headlamp Control Circuit Short to Ground
DTC B2699 04
-
Right Headlamp Control Circuit Open
Diagnostic Fault Information
Circuit/System Description
With the headlamp switch in the ON position, the headlamp ON signal circuit is grounded through the headlamp switch. The body control module (BCM) responds by applying current to the left and right low beam headlamp control circuits illuminating the low beam headlamps.
Conditions for Running the DTC
* Battery voltage must be between 9-16 V.
* Low beam headlamps ON.
Conditions for Setting the DTC
B2575 02
The BCM detects a short to ground in the left headlamp low beam control circuit.
B2575 04
The BCM detects an open in the left headlamp low beam control circuit or its B+ circuit or an open/high resistance in the left headlamp low beam ground circuit.
B2699 02
The BCM detects a short to ground in the right headlamp low beam control circuit.
B2699 04
The BCM detects an open in the right headlamp low beam control circuit or its B+ circuit or an open/high resistance on the right headlamp low beam ground circuit.
Actions Taken When the DTC Sets
When DTC B2575 or B2699 is present, the associated low beam headlamp will not operate.
Conditions for Clearing the DTC
* The condition responsible for setting the DTC no longer exists.
* A history DTC will clear once 100 consecutive malfunction-free ignition cycles have occurred.
Reference Information
Schematic Reference
Headlights/Daytime Running Lights (DRL) Schematics Headlights/Daytime Running Lights (DRL) Schematics
Connector End View Reference
Component Connector End Views Connector End Views By Name
Description and Operation
Exterior Lighting Systems Description and Operation Exterior Lighting Systems
Electrical Information Reference
* Circuit Testing Circuit Testing
* Connector Repairs Connector Repairs
* Testing for Intermittent Conditions and Poor Connections Testing for Intermittent Conditions and Poor Connections
* Wiring Repairs Wiring Repairs
Scan Tool Reference
Control Module References Programming and Relearning for scan tool information
Circuit/System Testing
1. Ignition OFF, disconnect the harness X1 harness connector at the K9 BCM.
2. Ignition ON, verify that a test lamp illuminates between the B+ circuit terminal listed below and ground:
* B+ circuit terminal 2
* B+ circuit terminal 3
• If the test lamp does not illuminate, test the B+ circuit for a short to ground or an open/high resistance.
3. Ignition OFF, connect the harness X1 harness connector at the K9 BCM.
4. Disconnect the harness connector at the appropriate E4 headlamp-low beam.
5. Test for less than 30 ohms between the ground circuit terminal 1 and ground.
• If greater than the specified range, test the ground circuit for an open/high resistance.
6. Connect a test lamp between the control circuit terminal 3 and ground.
7. Ignition ON, command the low beam lamps ON and OFF with a scan tool. The test lamp should turn ON and OFF while changing between the commanded states.
• If the test lamp is always ON, test the control circuit for a short to voltage. If the circuit tests normal, replace the K9 BCM.
• If the test lamp is always OFF, test the control circuit for a short to ground or an open/high resistance. If the circuit tests normal, replace the K9 BCM
8. If all circuits test normal, replace the headlamp bulb.
Repair Instructions
Perform the Diagnostic Repair Verification Verification Tests after completing the diagnostic procedure.
* Headlamp Replacement Headlamp Replacement
* Headlamp Bulb Replacement (TT4 Low Beam) Headlamp Bulb Replacement (TT4 Low Beam)Headlamp Bulb Replacement (TT4 High Beam) Headlamp Bulb Replacement (TT4 High Beam)
* Control Module References Programming and Relearning for BCM replacement, programming and setup