P1A05
DTC P1A01, P1A05, P1A06, or P1A5C
Diagnostic Instructions
* Perform the Diagnostic System Check - Vehicle Diagnostic System Check - Vehicle prior to using this diagnostic procedure.
* Review Strategy Based Diagnosis Strategy Based Diagnosis for an overview of the diagnostic approach.
* Diagnostic Procedure Instructions Diagnostic Procedure Instructions provides an overview of each diagnostic category.
DTC Descriptors
DTC P1A01
-
Battery Energy Control Module Long Term Memory Performance
DTC P1A05
-
Battery Energy Control Module Random Access Memory (RAM)
DTC P1A06
-
Battery Energy Control Module Read Only Memory (ROM)
DTC P1A5C
-
Battery Energy Control Module Main Processor Performance
Circuit/System Description
The battery energy control module performs various internal fault detection test to determine if a software or hardware concern exists within the module. No external circuits are involved.
Conditions for Running the DTC
P1A01, P1A05, P1A06
12 V battery voltage is greater than 8.8 V.
P1A5C
* Ignition ON
* 12 V battery voltage is greater than 8.8 V.
Conditions for Setting the DTC
An internal fault is detected in the battery energy control module.
Action Taken When the DTC Sets
No action is taken.
Conditions for Clearing the DTC
No internal faults are detected in the battery energy control module.
Reference Information
Schematic Reference
Hybrid Energy Storage Schematics [1][2]Electrical Diagrams
Connector End View Reference
Component Connector End Views Connector End Views By Name
Description and Operation
Drive Motor Battery System Description Drive Motor Battery System Description
Electrical Information Reference
* Circuit Testing Circuit Testing
* Connector Repairs Connector Repairs
* Testing for Intermittent Conditions and Poor Connections Testing for Intermittent Conditions and Poor Connections
* Wiring Repairs Wiring Repairs
DTC Type Reference
Powertrain Diagnostic Trouble Code (DTC) Type Definitions Powertrain Diagnostic Trouble Code (DTC) Type Definitions
Scan Tool Reference
Control Module References Programming and Relearning for scan tool information
Special Tools
EL-48900 - HEV Safety Kit
For equivalent regional tools, refer to Special Tools Tools and Equipment.
Circuit/System Verification
Danger:
Always perform the High Voltage Disabling procedure prior to servicing any High Voltage component or connection. Personal Protection Equipment (PPE) and proper procedures must be followed.
The High Voltage Disabling procedure will perform the following tasks:
* Identify how to disable high voltage.
* Identify how to test for the presence of high voltage.
* Identify condition under which high voltage is always present and personal protection equipment (PPE) and proper procedures must be followed.
Before working on any high voltage system, be sure to wear the following Personal Protection Equipment:
* Safety glasses with appropriate side shields when within 15 meters (50 feet) of the vehicle, either indoors or outdoors.
* Certified and up-to-date Class "0" Insulation gloves rated at 1000V with leather protectors.
- Visually and functionally inspect the gloves before use.
- Wear the Insulation gloves with leather protectors at all times when working with the high voltage battery assembly, whether the system is energized or not.
Failure to follow the procedures exactly as written may result in serious injury or death.
Danger:
The eAssist battery pack assembly will utilize an exchange program. Please consult the most recent revision of bulletin/PI# PIC5520, available in Service Information♦(SI), for a list of approved eAssist battery pack assembly service procedures. Components that may be removed and serviced without exchanging the complete battery pack assembly are identified in the bulletin/PI. Please contact the GM Technical Assistance Center (1-877-446-8227) if you have any questions.
1. Ignition ON.
2. Verify DTC P1A01, P1A05, P1A06, or P1A5C is not set.
• If any of the DTCs are set
Replace the K16 battery energy control module
• If none of the DTCs are set
3. All OK.
Repair Instructions
Perform the Diagnostic Repair Verification Verification Tests after completing the repair.
Control Module References Programming and Relearning for battery energy control module replacement, programming and setup