C0267

DTC C0267

Diagnostic Instructions

* Perform the Diagnostic System Check - Vehicle Diagnostic System Check - Vehicle prior to using this diagnostic procedure.

* Review Strategy Based Diagnosis Strategy Based Diagnosis for an overview of the diagnostic approach.

* Diagnostic Procedure Instructions Diagnostic Procedure Instructions provides an overview of each diagnostic category.

DTC Descriptor

DTC C0267 00
- Low Brake Fluid Indicated

Diagnostic Fault Information






Circuit/System Description

The brake fluid level switch monitors the level of brake fluid in the brake fluid reservoir. When the electronic brake control module sees the brake fluid level switch input open, the DTC is set.

Conditions for Running the DTC

Ignition ON.

Conditions for Setting the DTC

* An open is detected on the brake fluid level signal circuit for 20 s.

* Low brake fluid level is detected for 20 s.

Action Taken When the DTC Sets

* The electronic brake control module disables the traction control and stability control for the duration of the ignition cycle.

* The traction control/stability control-active indicator turns ON.

* The brake warning indicator turns ON.

Conditions for Clearing the DTC

The condition for setting the DTC is no longer present.

Reference Information

Schematic Reference

Hydraulic Brake Schematics [1][2]Electrical Diagrams

Connector End View Reference

Component Connector End Views Outside Rearview Mirror - Driver

Description and Operation

Hydraulic Brake System Description and Operation Hydraulic Brake System

Electrical Information Reference

* Circuit Testing Circuit Testing

* Connector Repairs Connector Repairs

* Testing for Intermittent Conditions and Poor Connections Testing for Intermittent Conditions and Poor Connections

* Wiring Repairs Wiring Repairs

Scan Tool Reference

Control Module References Control Module References for scan tool information

Circuit/System Verification

1. Verify that the brake fluid has the proper level. The fluid level should be above minimum level.

• If low
Refer to Brake Fluid Loss Brake Fluid Loss.

• If above minimum level

2. Ignition ON.

3. Verify the scan tool Brake Fluid Level Sensor parameter is Ok.

• If the parameter is Low
Refer to Circuit/System Testing.

• If the parameter is Ok

4. All OK.

Circuit/System Testing

1. Ignition OFF, disconnect the harness connector at the B20 Brake Fluid Level Switch.

2. Test for less than 10 ohms between the ground circuit terminal 2 and ground.

• If 10 ohms or greater

1. Ignition OFF.

2. Test for less than 2 ohms in the ground circuit end to end.

• If 2 ohms or greater, repair the open/high resistance in the circuit.

• If less than 2 ohms, repair the open/high resistance in the ground connection.

• If less than 10 ohms

3. Ignition ON.

4. Verify the scan tool Brake Fluid Level Sensor parameter is Low.

• If the parameter is not Low

1. Ignition OFF, disconnect the harness connector at the K17 Electronic Brake Control Module.

2. Test for infinite resistance between the signal circuit terminal 1 and ground.

• If less than infinite resistance, repair the short to ground on the circuit.

• If infinite resistance, replace the K17 Electronic Brake Control Module.

• If the parameter is Low

5. Install a 3 A fused jumper wire between the signal circuit terminal 1 and ground.

6. Verify the scan tool Brake Fluid Level Sensor parameter is Ok.

• If the parameter is not Ok

1. Ignition OFF, disconnect the harness connector at the K17 Electronic Brake Control Module, ignition ON.

2. Test for less than 1 V between the signal circuit and ground.

• If 1 V or greater, repair the short to voltage on the circuit.

• If less than 1 V.

3. Test for less than 2 ohms in the signal circuit end to end.

• If 2 ohms or greater, repair the open/high resistance in the circuit.

• If less than 2 ohms, replace the K17 Electronic Brake Control Module.

• If the parameter is Ok

7. Test or replace the B20 Brake Fluid Level Switch.

Repair Instructions

Perform the Diagnostic Repair Verification Verification Tests after completing the repair.

* Brake Fluid Level Indicator Switch Replacement Service and Repair

* Control Module References Control Module References for Electronic Brake Control Module replacement, programming and setup