P0796
DTC P0796 or P0797 (Gen 2 with 2.4L - LEA)
Diagnostic Instructions
* Perform the Diagnostic System Check - Vehicle Diagnostic System Check - Vehicle prior to using this diagnostic procedure.
* Review Strategy Based Diagnosis Strategy Based Diagnosis for an overview of the diagnostic approach.
* Diagnostic Procedure Instructions Diagnostic Procedure Instructions provides an overview of each diagnostic category.
DTC Descriptors
DTC P0796
- Pressure Control Solenoid Valve 3 Stuck Off
DTC P0797
- Pressure Control Solenoid Valve 3 Stuck On
Circuit/System Description
The clutch pressure control solenoid 3 is part of the control solenoid valve assembly which has no serviceable components. Pressure control solenoid 3 regulates transmission fluid pressure to the R1/4-5-6 regulator valve which controls pressure to the reverse and low clutch and the 4-5-6 clutch. The transmission control module (TCM) calculates gear ratio based on the speed signals from the automatic transmission input shaft speed (ISS) sensor and the output shaft speed (OSS) sensor. The TCM compares the expected transmission gear ratio to the calculated gear ratio for each commanded gear.
Conditions for Running the DTC
P0796
* DTC P0101, P0102, P0103, P0106, P0107, P0108, P0171, P0172, P0174, P0175, P0201, P0202, P0203, P0204, P0205, P0206, P0207, P0208, P0300, P0301, P0302, P0303, P0304, P0305, P0306, P0307, P0308, P0401, P042E, P0716, P0717, P0722, P0723, or P182E is not set.
* Engine speed is 400-7500 RPM for 5 seconds.
* Transmission output speed is 100 RPM or greater or the throttle position is 0.5 percent or greater.
* Ignition voltage is 9-32 V.
* Transmission fluid temperature is -6.7°C (20°F) or greater.
* High side driver is enabled.
* Throttle position signal is valid.
P0797
* DTC P0101, P0102, P0103, P0106, P0107, P0108, P0171, P0172, P0174, P0175, P0201, P0202, P0203, P0204, P0205, P0206, P0207, P0208, P0300, P0301, P0302, P0303, P0304, P0305, P0306, P0307, P0308, P0401, P042E, P0716, P0717, P0722, P0723, or P182E is not set.
* Engine speed is 400-7500 RPM for 5 seconds.
* Transmission output speed is 100 RPM or greater or the throttle position is 0.5 percent or greater.
* Throttle position signal is valid.
* Ignition voltage is 9-32 V.
* Transmission fluid temperature is -6.7°C (20°F) or greater.
* High side driver is enabled.
* The throttle position is 10 percent or greater and the engine torque is 45 Nm (33 lb ft) or greater if attained gear is 1st free wheel.
Conditions for Setting the DTC
P0796
The TCM detects an incorrect gear ratio when the 4-5-6 clutch is commanded ON. This condition must occur 3 times.
P0797
The TCM detects an incorrect gear ratio change when the 4-5-6 clutch is commanded OFF during a shift. This must occur 3 times.
Action Taken When the DTC Sets
P0796
* DTC P0796 is a Type A DTC.
* TCM commands maximum line pressure.
* TCM freezes transmission adaptive functions.
* TCM inhibits TAP Up/TAP Down functions.
* TCM inhibits manual up, manual down shifts with the shift selector.
* TCM limits the transmission to reverse and 3rd gear.
* TCM inhibits powertrain braking.
* TCM inhibits neutral idle.
* TCM inhibits auto grade braking.
P0797
* DTC P0797 is a Type A DTC.
* TCM commands maximum line pressure.
* TCM freezes transmission adaptive functions.
* TCM inhibits TAP Up/TAP Down functions.
* TCM inhibits manual up, manual down shifts with the shift selector.
* TCM limits the transmission to reverse and 4th gear.
* TCM inhibits powertrain braking.
* TCM requests a reduced amount of engine torque based on input speed.
* TCM inhibits neutral idle.
* TCM inhibits auto grade braking.
Conditions for Clearing the DIC/DTC
DTCs P0796 and P0797 are Type A DTCs.
Diagnostic Aids
Before performing a road test, configure and setup the scan tool for snapshot mode. This allows you to monitor, display, and verify multiple transmission data parameters at one time, after the road test.
Reference Information
Schematic Reference
Automatic Transmission Controls Schematics Electrical Diagrams
Connector End View Reference
* Component Connector End Views Outside Rearview Mirror - Driver
* Inline Harness Connector End Views X100
Description and Operation
* Transmission General Description Transmission General Description
* Transmission Component and System Description Transmission Component and System Description
* Electronic Component Description Electronic Component Description
* Drive Range - Fourth Gear (Gen 2/Hybrid) Drive Range - Fourth Gear (Gen 2/Hybrid)
* Drive Range, Fifth Gear (Gen 2/Hybrid) Drive Range, Fifth Gear (Gen 2/Hybrid)
* Drive Range, Sixth Gear (Gen 2/Hybrid) Drive Range, Sixth Gear (Gen 2/Hybrid)
Electrical Information Reference
* Circuit Testing Circuit Testing
* Connector Repairs Connector Repairs
* Testing for Intermittent Conditions and Poor Connections Testing for Intermittent Conditions and Poor Connections
* Wiring Repairs Wiring Repairs
DTC Type Reference
Powertrain Diagnostic Trouble Code (DTC) Type Definitions Powertrain Diagnostic Trouble Code (DTC) Type Definitions
Scan Tool Reference
Control Module References Control Module References for scan tool information
Special Tools
* DT-48616 - Solenoid Assembly Test Kit & Adapter Harness
* J 21867 - Pressure Gauge
For equivalent regional tools, refer to Special Tools Tools and Equipment.
Circuit/System Verification
Warning: Refer to Parking Brake and Drive Wheels Warning Parking Brake and Drive Wheels Warning.
1. Ignition ON, engine OFF.
2. Verify DTC P0716, P0717, P0722, P0723, P077C, P077D, P07BF, or P07C0 was not set by reviewing the scan tool Freeze Frame/Failure Records data.
• If a DTC was set
Refer to Diagnostic Trouble Code (DTC) List - Vehicle Diagnostic Trouble Code (DTC) List - Vehicle.
• If a DTC is not set
3. Engine idling in Park, with parking brake applied and drive wheels chocked.
4. Verify correct transmission fluid level and condition. Refer to Transmission Fluid Level and Condition Check Transmission Fluid Level and Condition Check.
• If the transmission fluid level and condition is not correct
Repair as necessary.
• If the transmission fluid level and condition is correct
5. Ignition ON, clear the TCM DTCs with a scan tool.
6. Verify DTC P0796 or P0797 does not set while performing a road test. Refer to Road Test Initial Inspection and Diagnostic Overview.
• If DTC P0796 or P0797 sets
Refer to Circuit/System Testing.
• If DTC P0796 or P0797 does not set
7. Operate the vehicle within the Conditions for Running the DTC. You may also operate the vehicle within the conditions that you observed from the Freeze Frame/Failure Records data.
8. Verify the DTC does not set.
• If a DTC sets
Refer to Circuit/System Testing.
• If a DTC does not set
9. All OK
Circuit/System Testing
Note: You must perform the Circuit/System Verification first.
1. Engine idling at the normal operating temperature.
2. Verify the transmission line pressures are within the specified range. Refer to Line Pressure Check Line Pressure Check and Solenoid Valve Pressure (Gen 1) Solenoid Valve Pressure (Gen 1)Solenoid Valve Pressure (Gen 2 with 2.4L - LEA) Solenoid Valve Pressure (Gen 2 with 2.4L - LEA).
• If the pressures are not within range
Refer to Fluid Pressure High or Low Fluid Pressure High or Low.
• If the pressures are within range
3. Ignition OFF, remove the Q8 Control Solenoid Valve Assembly.
4. Verify a pressure change occurs for all solenoids when performing the solenoid test. Refer to Control Solenoid Valve and Transmission Control Module Assembly Solenoid Performance Test Control Solenoid Valve and Transmission Control Module Assembly Solenoid Performance Test.
• If a pressure change does not occur
Replace the Q8 Control Solenoid Valve Assembly.
• If a pressure change occurs
5. Verify the mechanical conditions listed below do not exist. Repair or replace as necessary.
P0796 or P0797 - Control Valve Body Assembly
4-5-6 Regulator Valve stuck/sticking - debris, binding, damaged valve, or scored bore.
P0796 - Transmission Cooling/Lubrication
* Restriction/leak in OAC, oil to air, cooler/radiator.
* Restricted/leaking/kinked/damaged transmission oil cooler lines.
* Restriction/leak in transmission fluid pump assembly.
P0796 - Automatic Transmission Fluid Filter Assembly
Oil filter or filter seal loose or damaged.
P0796 - Input Shaft Support
Input shaft tower seals damaged or leaking.
P0796 - 4-5-6 Clutch Housing Assembly
4-5-6 Clutch Piston Assembly damaged/leaking.
P0796 - Torque Converter (w/Fluid Pump) Housing Assembly
* Fluid pump housing vanes/rotor/slide damaged/scored.
* Fluid pump or torque converter overstressed due to high temperature.
P0796 - 4-5-6 Reaction Carrier Hub Assembly
4-5-6 Reaction Carrier Hub/Shaft - broken hub weld.
P0796 - 3-5-R and 4-5-6 Clutch Housing Assembly
4-5-6 Clutch Backing Plate Retaining Ring not seated/oriented, causing clutch pack/piston overtravel.
PO796 Output Carrier Assembly
Output carrier pinion pins too high or too low.
P0796 or P0797 - Q8 Control Solenoid Valve Assembly
* Clutch Pressure Control Solenoid 3 stuck ON/OFF.
* O-ring seals leaking.
* Valve body filter plate assembly cracked, blocked, or damaged gasket seal.
Repair Instructions
Perform the Diagnostic Repair Verification Verification Tests after completing the repair.
* Control Solenoid Valve and Transmission Control Module Assembly Replacement Service and Repair
* Perform the Transmission Adaptive Values Learn Programming and Relearning following all transmission repairs.
* Control Module References Control Module References for control solenoid valve assembly replacement, programming and setup.