Procedures
Plastic Collar Quick Connect Fitting Service
Plastic Quick Connect Fitting Type Identification
Plastic Quick Connect Fitting Type A
Quick connect fitting type A - TI loc with one latch (1).
Plastic Quick Connect Fitting Type B
* Quick connect fitting type B - TI loc upper latch (1).
* Quick connect fitting type B - TI loc lower latch (2).
Plastic Quick Connect Fitting Type C
Quick connect fitting type C (1).
Plastic Quick Connect Fitting Type D
Quick connect fitting type D (1).
Plastic Quick Connect Fitting Type E
Quick connect fitting type E (1).
Plastic Quick Connect Fitting Type F
Quick connect fitting type F (1).
Plastic Quick Connect Fitting Type G
Quick connect fitting type G (1).
General Instructions for Handling the Connectors
Before Disconnection
Warning
Wear safety glasses when using compressed air, as flying dirt particles may cause eye injury.
Note: The following instructions apply to all of these types of fittings.
Using compressed air, to blow any dirt out of the quick connect fitting.
After Disconnection
* Wipe off the male pipe end using a clean shop towel.
* Inspect both ends of the fitting for dirt and burrs.
* Clean components as required.
* Replace damaged components.
Type A - Disconnect/Connect
Disconnect
Note: Mechanical violence is not necessary for a successful disconnection/connection.
1. Push the tube (3) into the connector (1) and push down the latch (2).
2. Push the latch (2) into the connector (1).
3. Pull the pipe (3) out of the connector (1).
4. Release the latch (2).
Connect
1. Push the pipe (3) into the connector (1).
2. When the connector is locked correctly, the latch (2) must align to the connector (1).
3. Do not rely only on the audible click to confirm a secure connection has been made.
4. Pull on both sides of the quick connect fitting in order to make sure the connection is secure.
Type B - Disconnect/Connect
Disconnect
Note: Mechanical violence is not necessary for a successful disconnection/connection.
1. Unlock the connector by pulling the latch (1) out of the connector. Use a suitable tool if necessary.
2. Push the pipe (3) into the connector (1).
3. Push the latch (1) into the connector.
4. Pull the pipe (2) out of the connector (1).
5. Release the latch.
Connect
1. Push the pipe (2) into the connector (1).
2. When the connector is locked correctly, the latch (1) must align to the connector.
Note: The latch (2) can only pushed into the connector (1) when the pipe (3) is connected correctly.
3. Push the latch (2) into the connector (1) to secure the connection.
4. Do not rely only on the audible click to confirm a secure connection has been made.
5. Pull on both sides of the quick connect fitting in order to make sure the connection is secure.
Type C - Disconnect/Connect
Disconnect
Note: Mechanical violence is not necessary for a successful disconnection/connection.
1. Squeeze the plastic quick connect fitting release tabs with the EN-796-A - release tool.
Quick Connect Fittings:
2. Pull the connection apart.
Connect
1. Push both sides of the quick connect fitting together in order to cause the retaining feature to snap into place.
2. Do not rely only on the audible click to confirm a secure connection has been made.
3. Once installed, pull on both sides of the quick connect fitting in order to make sure the connection is secure.
Type D - Disconnect/Connect
Disconnect
Note: Mechanical violence is not necessary for a successful disconnection/connection.
1. Release the fitting by pushing the tab toward the other side of the slot in the fitting.
Quick Connect Fittings:
2. Pull the connection apart.
Connect
1. Push both sides of the quick connect fitting together in order to cause the retaining feature to snap into place.
2. Do not rely only on the audible click to confirm a secure connection has been made.
3. Once installed, pull on both sides of the quick connect fitting in order to make sure the connection is secure.
Type E - Disconnect/Connect
Disconnect
Note: Mechanical violence is not necessary for a successful disconnection/connection.
1. Squeeze where indicated by arrows on both sides of the plastic ring surrounding the quick connect fitting.
Quick Connect Fittings:
2. Pull the connection apart.
Connect
1. Push both sides of the quick connect fitting together in order to cause the retaining feature to snap into place.
2. Do not rely only on the audible click to confirm a secure connection has been made.
3. Once installed, pull on both sides of the quick connect fitting in order to make sure the connection is secure.
Type F - Disconnect/Connect
Disconnect
Note: Mechanical violence is not necessary for a successful disconnection/connection.
1. Release the fitting by pressing on one side of the release tab causing it to push in slightly. If the tab does not move, try pressing the tab in from the opposite side. The tab will only move in one direction.
Quick Connect Fittings:
2. Pull the connection apart.
Connect
1. Push both sides of the quick connect fitting together in order to cause the retaining feature to snap into place.
2. Do not rely only on the audible click to confirm a secure connection has been made.
3. Once installed, pull on both sides of the quick connect fitting in order to make sure the connection is secure.
Type G - Disconnect/Connect
Disconnect
Note: Mechanical violence is not necessary for a successful disconnection/connection.
1. Push the tube (3) into the connector (1) and push down the latch (2) as the arrow shows.
2. Hold the latch (2) in this position.
3. Pull the pipe (3) out of the connector (1).
4. Release the latch (2).
Connect
1. Push the pipe (3) into the connector (1).
2. When the connector is locked correctly, the latch (2) must go back in opposite arrow direction.
3. Do not rely only on the audible click to confirm a secure connection has been made.
4. Pull on both sides of the quick connect fitting in order to make sure the connection is secure.