Removal and Replacement

Transmission Replacement
^ Tools Required
- J 21366 Converter Holding Strap

Removal Procedure





1. Disconnect the negative battery cable. Refer to Battery Negative Cable Disconnect/Connect Procedure in Starting and Charging.
2. Drain the transmission fluid.
3. Remove the rear propeller shaft.
4. Support the transmission with a transmission jack.
5. Remove the transmission mount nuts.





6. Remove the transmission support bolts/nuts.
7. Raise the transmission slightly and remove the transmission support from the vehicle.
8. Remove the exhaust pipe.
9. Remove the starter motor.
10. Remove the transfer case, if equipped. Refer to the appropriate procedure:
^ Transfer Case - BW 4481 - NR3 Transfer Case Assembly Replacement in Driveline/Axle.
^ Transfer Case - BW 4482 - NR4 Transfer Case Assembly Replacement in Driveline/Axle.
^ Transfer Case - NVG 246 - NP8 Transfer Case Assembly Replacement in Driveline/Axle.





11. Remove the transmission mount bolts and mount.





12. Ensure the transmission manual shaft is positioned in mechanical park.
13. Remove the retainer that secures the cable to the bracket.





14. Remove the range selector cable end (2) from the transmission range selector lever ball stud (1).
15. Depress the tangs and remove the cable from the bracket.





16. Remove the exhaust hanger bracket bolts and bracket.





17. Remove the harness clip (1) from the fuel line bracket.
18. Disconnect the park/neutral position (PNP) switch electrical connectors (2).





19. Disconnect the main electrical connector (1).
20. Disconnect the vehicle speed sensor (VSS) electrical connector (2).





21. Remove the bolt that secures the fuel line bracket to the left side of the transmission.





22. Remove the torque converter bolts.





23. Disconnect the transmission oil cooler lines. Refer to Transmission Oil Cooler Line Quick Connect Fitting.
24. Plug the transmission oil cooler line fittings.





25. Remove the fuel feed/return and evaporative emission (EVAP) return pipe bracket nut.





26. Remove the lower right transmission bolt and stud.





27. Remove the remaining transmission studs and bolt.
28. Install the J 21366 onto the transmission in order to retain the torque converter.
29. Pull the transmission straight back.
30. Remove the transmission from the vehicle while simultaneously removing the fluid level indicator tube.
31. Install the J 21366 to the bell housing in order to retain the torque converter.
32. Flush the transmission oil cooler and cooling lines if necessary.

Installation Procedure





1. Raise the transmission into place while simultaneously installing the fluid indicator tube.
2. Remove the J 21366.
3. Slide the transmission straight onto the locating pins while lining up the marks on the flywheel and the torque converter. The torque converter must rotate freely by hand.

Notice: Refer to Fastener Notice in Service Precautions.

4. Install transmission studs and bolt.
^ Tighten the bolt/studs to 50 Nm (37 ft. lbs.).





5. Install the lower right transmission stud and bolt.
^ Tighten the bolt/stud to 50 Nm (37 ft. lbs.).





6. Install the fuel feed/return and EVAP return pipe bracket nut.
^ Tighten the nut to 20 Nm (15 ft. lbs.).





7. Remove the plugs from the transmission oil cooler line fittings.
8. Connect the transmission oil cooler lines. Refer to Transmission Oil Cooler Line Quick Connect Fitting.





9. Install the torque converter bolts.
^ Tighten the bolts to 63 Nm (46 ft. lbs.).





10. Install the bolt that secures the fuel line bracket to the left side of the transmission.
^ Tighten the bolt to 10 Nm (89 inch lbs.).





11. Connect the VSS electrical connector (2).
12. Connect the main electrical connector (1).





13. Connect the PNP switch electrical connectors (2).
14. Install the harness clip (1) to the fuel line bracket.





15. Install the exhaust hanger bracket and bolts
^ Tighten the bolts to 17 Nm (13 ft. lbs.).





16. Install the cable to the bracket.
17. Install the range selector cable end (2) to the transmission range selector lever ball stud (1).





18. Ensure the transmission manual shaft is positioned in mechanical park.
19. Install the retainer that secures the cable to the bracket.





20. Install the transmission mount and bolts.
^ Tighten the bolts to 25 Nm (18 ft. lbs.).
21. Install the transfer case, if equipped. Refer to the appropriate procedure:
^ Transfer Case - BW 4481 - NR3 Transfer Case Assembly Replacement in Driveline/Axle.
^ Transfer Case - BW 4482 - NR4 Transfer Case Assembly Replacement5 in Driveline/Axle.
^ Transfer Case - NVG 246 - NP8 Transfer Case Assembly Replacement in Driveline/Axle.
22. Install the starter motor.





24. Raise the transmission slightly and install the transmission support.
25. Install the transmission support bolts/nuts.
^ Tighten the bolts/nuts to 95 Nm (70 ft. lbs.).





26. Install the transmission mount nuts.
^ Tighten the nuts to 50 Nm (37 ft. lbs.).
27. Remove the support from the transmission.
28. Install the rear propeller shaft. Refer to Propeller Shaft Replacement - Rear in Propeller Shaft.
29. Connect the negative battery cable.
30. Fill the transmission to the proper level with DEXRON(R) III transmission fluid. Refer to Transmission Fluid Checking Procedure.