C0297

DTC C0297

Diagnostic Instructions

* Perform the Diagnostic System Check - Vehicle (Initial Inspection and Diagnostic Overview) prior to using this diagnostic procedure.
* Review Strategy Based Diagnosis (Initial Inspection and Diagnostic Overview) for an overview of the diagnostic approach.
* Diagnostic Procedure Instructions (Initial Inspection and Diagnostic Overview) provides an overview of each diagnostic category.



DTC Descriptor
DTC C0297 00
- Brake Applied Output Circuit




Diagnostic Fault Information






Circuit/System Description

North America

The brake pedal position sensor is used to sense the action of the driver application of the brake pedal. The brake pedal position sensor provides an analog voltage signal that will increase as the brake pedal is applied. The body control module (BCM) provides a low reference signal and a 5-volt reference voltage to the brake pedal position sensor. When the variable signal reaches a voltage threshold indicating the brakes have been applied, the BCM will apply battery voltage to the right and left stop lamp control circuits, transmission control module (TCM), engine control module (ECM), and center high mounted stop lamp (CHMSL) control circuit.

European

The brake pedal position sensor is used to sense the action of the driver application of the brake pedal. The brake pedal position sensor provides an analog voltage signal that will increase as the brake pedal is applied. The body control module (BCM) provides a low reference signal and a 5-volt reference voltage to the brake pedal position sensor. When the variable signal reaches a voltage threshold indicating the brakes have been applied, the BCM will apply battery voltage to stop lamp relay coil side control circuit, transmission control module (TCM), engine control module (ECM), and center high mounted stop lamp (CHMSL). When the stop lamp relay receives battery voltage from the BCM, the relay coil is energized and the stop lamp relay switch contacts close applying battery voltage from the STOP LAMPS fuse to illuminate the rear stop lamps and trailer stop lamps.


Conditions for Running the DTC

Battery voltage must be between 9-16 volts.


Conditions for Setting the DTC

DTC C0297 00 will set when the BCM detects a short to ground or a short to voltage in the stop lamp switch signal circuit.


Actions Taken When the DTC Sets

* The BCM stores the DTC to memory.
* The Service Vehicle Soon indicator is commanded ON.



Conditions for Clearing the DTC

* The condition responsible for setting the DTC no longer exists.
* You issue a scan tool CLEAR DTCs command.
* A history DTC will clear once 40 malfunction-free ignition cycles have occurred.



Diagnostic Aids

Important: The stop lamps will not illuminate unless the ignition is in the ON position. For more detailed information concerning stop lamp operation, refer to Exterior Lighting Systems Description and Operation (Exterior Lighting Systems Description and Operation) .



Verify that the brake pedal position sensor is properly calibrated.


Reference Information
Schematic Reference

Exterior Lights Schematics (Exterior Lights Schematics)
Connector End View Reference

Component Connector End Views (Connector Views)
Description and Operation

Exterior Lighting Systems Description and Operation (Exterior Lighting Systems Description and Operation)
Electrical Information Reference

* Circuit Testing (Component Tests and General Diagnostics)
* Connector Repairs (Component Tests and General Diagnostics)
* Testing for Intermittent Conditions and Poor Connections (Component Tests and General Diagnostics)
* Wiring Repairs (Component Tests and General Diagnostics)

Scan Tool Reference

Control Module References (Programming and Relearning) for scan tool information


Circuit/System Testing

1. Ignition OFF, disconnect the harness connector at the ECM.
2. Connect a test lamp between the stop lamp switch signal circuit and ground.
3. Ignition ON, command the stop lamps ON and OFF with a scan tool. The test lamp should turn ON and OFF when changing between the commanded states.

• If the test lamp is always ON, test the signal circuit for a short to voltage. If the circuit tests normal, replace the BCM.
• If the test lamp is always OFF, test the signal circuit for a short to ground or an open/high resistance. If the circuit tests normal, replace the BCM.

4. Ignition OFF, connect a test lamp between the stop lamp switch signal circuit and the connector terminal at the ECM.
5. Ignition ON, command the stop lamps ON and OFF with a scan tool. The test lamp should turn ON and OFF when changing between the commanded states.

• If the test lamps does not operate as described, replace the ECM.

6. Ignition OFF, reconnect the ECM harness connector.
7. Disconnect the harness connector at the TCM.
8. Connect a test lamp between the stop lamp switch signal circuit and ground.
9. Ignition ON, command the stop lamps ON and OFF with a scan tool. The test lamp should turn ON and OFF when changing between the commanded states.

• If the test lamp is always ON, test the signal circuit for a short to voltage. If the circuit tests normal, replace the BCM.
• If the test lamp is always OFF, test the signal circuit for a short to ground or an open/high resistance. If the circuit tests normal, replace the BCM.

10. If all circuits test normal, replace the TCM.



Repair Instructions

Perform the Diagnostic Repair Verification (Verification Tests) after completing the diagnostic procedure.

* Brake Pedal Position Sensor Calibration (Programming and Relearning)
* Brake Pedal Position Sensor Replacement (Brake Pedal Position Sensor Replacement)
* Control Module References (Programming and Relearning) for BCM, ECM, or TCM replacement, setup, and programming