C0890

DTC C0890

Diagnostic Instructions

* Perform the Diagnostic System Check - Vehicle (Initial Inspection and Diagnostic Overview) prior to using this diagnostic procedure.
* Review Strategy Based Diagnosis (Initial Inspection and Diagnostic Overview) for an overview of the diagnostic approach.
* Diagnostic Procedure Instructions (Initial Inspection and Diagnostic Overview) provides an overview of each diagnostic category.



DTC Descriptors
DTC C0890 03
- Device Voltage Reference Output 3 Circuit Voltage Below Threshold

DTC C0890 07
- Device Voltage Reference Output 3 Circuit Voltage Above Threshold




Diagnostic Fault Information






Circuit/System Description

North America

The brake pedal position sensor is used to sense the action of the driver application of the brake pedal. The brake pedal position sensor provides an analog voltage signal that will increase as the brake pedal is applied. The body control module (BCM) provides a low reference signal and a 5-volt reference voltage to the brake pedal position sensor. When the variable signal reaches a voltage threshold indicating the brakes have been applied, the BCM will apply battery voltage to the right and left stop lamp control circuits, transmission control module (TCM), engine control module (ECM), and center high mounted stop lamp (CHMSL) control circuit.

European

The brake pedal position sensor is used to sense the action of the driver application of the brake pedal. The brake pedal position sensor provides an analog voltage signal that will increase as the brake pedal is applied. The body control module (BCM) provides a low reference signal and a 5-volt reference voltage to the brake pedal position sensor. When the variable signal reaches a voltage threshold indicating the brakes have been applied, the BCM will apply battery voltage to stop lamp relay coil side control circuit, transmission control module (TCM), engine control module (ECM), and center high mounted stop lamp (CHMSL). When the stop lamp relay receives battery voltage from the BCM, the relay coil is energized and the stop lamp relay switch contacts close applying battery voltage from the STOP LAMPS fuse to illuminate the rear stop lamps and trailer stop lamps.


Conditions for Running the DTC

Battery voltage must be between 9-16 volts.


Conditions for Setting the DTC

C0890 03

The DTC will set when the BCM detects a short to ground in the brake pedal position sensor voltage reference circuit for 0.5 seconds or greater.

C0890 07

The DTC will set when the BCM detects a short to battery voltage in the brake pedal position sensor voltage reference circuits for 0.5 seconds or greater.


Actions Taken When the DTC Sets

* The Service Vehicle Soon indicator is commanded ON.
* If the DTC sets while the vehicle is running, the BCM will activate the brake lights when the vehicles transmission is not in the PARK position and the vehicle is not accelerating.



Conditions for Clearing the DTC

* The condition responsible for setting the DTC no longer exists.
* You issue a scan tool CLEAR DTCs command.
* A history DTC will clear once 50 malfunction-free ignition cycles have occurred.
* A DTC will not clear the current status until the next ignition cycle.



Diagnostic Aids

The stop lamps will not illuminate unless the ignition is in the ON position. For more detailed information concerning stop lamp operation, refer to Exterior Lighting Systems Description and Operation (Exterior Lighting Systems Description and Operation) .


Reference Information
Schematic Reference

Exterior Lights Schematics (Exterior Lights Schematics)
Connector End View Reference

Component Connector End Views (Connector Views)
Description and Operation

Exterior Lighting Systems Description and Operation (Exterior Lighting Systems Description and Operation)
Electrical Information Reference

* Circuit Testing (Component Tests and General Diagnostics)
* Connector Repairs (Component Tests and General Diagnostics)
* Testing for Intermittent Conditions and Poor Connections (Component Tests and General Diagnostics)
* Wiring Repairs (Component Tests and General Diagnostics)

Scan Tool Reference

Control Module References (Programming and Relearning) for scan tool information


Circuit/System Testing

1. Ignition OFF, disconnect the harness connector at the brake pedal position sensor.
2. Ignition OFF, verify that a test lamp illuminates between B+ and the low reference circuit terminal B.

• If the test lamp does not illuminate, test the low reference circuit for an open/high resistance.

3. Ignition ON, test for 4.8-5.2 volts between the 5-volt reference circuit terminal C and ground.

• If less than the specified range, test the 5-volt reference circuit for a short to ground or an open/high resistance. If the circuit tests normal, replace the BCM.
• If greater than the specified range, test the 5-volt reference circuit for a short to voltage. If the circuit tests normal, replace the BCM.

4. If all circuits test normal, test or replace the brake pedal position sensor.



Repair Instructions

Perform the Diagnostic Repair Verification (Verification Tests) after completing the diagnostic procedure.

* Brake Pedal Position Sensor Calibration (Programming and Relearning)
* Brake Pedal Position Sensor Replacement (Brake Pedal Position Sensor Replacement)
* Control Module References (Programming and Relearning) for BCM replacement, setup, and programming