Rear Drive Axle
DTC C0574
Diagnostic Instructions
* Perform the Diagnostic System Check - Vehicle (Diagnostic System Check - Vehicle) prior to using this diagnostic procedure.
* Review Strategy Based Diagnosis (Strategy Based Diagnosis) for an overview of the diagnostic approach.
* Diagnostic Procedure Instructions (Diagnostic Procedure Instructions) provides an overview of each diagnostic category.
DTC Descriptors
DTC C0574 02
- Printed Circuit Board Temperature Sensor Short to Ground
DTC C0574 04
- Printed Circuit Board Temperature Sensor Open
DTC C0574 13
- Printed Circuit Board Temperature Sensor Low Voltage/High Temperature
DTC C0574 14
- Printed Circuit Board Temperature Sensor High Voltage/Low Temperature
Diagnostic Fault Information
Circuit/System Description
A temperature sensor is installed on the circuit board of the rear differential clutch control module. The sensor is used for calculating the module circuit board and differential clutch fluid temperature.
Conditions for Running the DTC
* The ignition is ON.
* The test runs with a frequency of 50 Hz.
Conditions for Setting the DTC
C0574 02
The analog-digital converter circuit is shorted to ground for more than 3 seconds.
C0574 04
The analog-digital converter circuit is open for more than 3 seconds.
C0574 13
The board temperature is greater than 115°C (239°F) for more than 3 seconds.
C0574 14
The board temperature is less than -40°C (-40°F) for more than 3 seconds.
Action Taken When the DTC Sets
One or more of the following actions may occur:
* All-wheel drive (AWD) is disabled.
* Service Rear Axle is displayed on the driver information center.
Conditions for Clearing the DTC
C0574 02 and C0574 04
* The condition for setting the DTC is no longer present.
* The circuit is not tested unless the ignition is cycled.
C0574 13 and C0574 14
* The temperature is within the limit for more than 30 s.
* The circuit is tested with a frequency of 50 Hz.
Diagnostic Aids
C0574 13 and C0574 14
The DTCs C0574 13 and C0574 14 indicate that the rear differential clutch control module temperature is out of range. This is a temporary fault. The rear differential clutch control module is protected against running during critical temperatures. As soon as the temperature reaches normal values the actual DTC is cleared.
Reference Information
Schematic Reference
Rear Axle Schematics (Electrical Diagrams)
Connector End View Reference
Component Connector End Views (Connector End Views By Name)
Description and Operation
Rear Drive Axle Description and Operation (Description and Operation)
Electrical Information Reference
* Circuit Testing (Circuit Testing)
* Connector Repairs (Connector Repairs)
* Testing for Intermittent Conditions and Poor Connections (Testing for Intermittent Conditions and Poor Connections)
* Wiring Repairs (Wiring Repairs)
Scan Tool Reference
Control Module References (Programming and Relearning) for scan tool information
Circuit/System Verification
Ignition ON, observe the scan tool Rear Differential Clutch Control Module Temperature parameter. The scan tool should display be between -40°C (-40°F) and 115°C (239°F) when stationary.
Circuit/System Testing
Important: The rear drive clutch solenoid valve is calibrated with and is part of the rear differential clutch control module. Both components must be replaced as a matched set.
C0574 02 and 0574 04
Ignition ON. Verify that DTC C0574 02 or 0574 04 is not set.
If a DTC is set, replace the K47 rear differential clutch control module.
C0574 13 and 0574 14
1. Ignition OFF, allow the housing and the K47 rear differential clutch control module temperature to adjust to within 0-40°C (32-104°F).
2. Ignition ON, verify that DTC C0574 13 or C0574 14 is not set.
If a DTC is set, replace the K47 rear differential clutch control module.
Repair Instructions
Perform the Diagnostic Repair Verification (Verification Tests) after completing the diagnostic procedure.
Control Module References (Programming and Relearning) for rear differential clutch control module replacement, setup, and programming