Timing Belt Replacement
Timing Belt Replacement
Removal Procedure
Tools Required
- J 42069 Timing Belt Alignment Kit
- J 42098 Crank Hub Torx Socket
Notice: Failure to follow this procedure could result in severe engine damage.
Notice: After timing belt is removed, never turn camshaft and crankshaft independently. If turned, interference may occur among pistons and valves, and parts related to pistons and valves may be damaged.
1. Disconnect the negative battery cable.
Caution: Refer to battery disconnect Caution in Caution and Notices.
2. Remove the intake air resonator.
3. Remove the timing belt cover.
4. Remove the harmonic balancer bolts.
5. Remove the harmonic balancer from the crankshaft drive gear.
6. Rotate the crankshaft clockwise to 60 degrees Before Top Dead Center (BTDC).
7. Install the J 42069-10 Crankshaft Locking Tool to the crankshaft drive gear with the knurled bolt.
8. Use the J 42098 Crank Hub Torx Socket to carefully turn the crankshaft in the engine rotational direction (clockwise) until the lever of the J 42069-10 Crankshaft Locking Tool firmly contacts the water pump pulley flange.
9. Secure the moveable lever of the tool to the water pump pulley flange.
Important: Ensure that the alignment of the crankshaft is not 180 degrees off.
The alignment marks on the camshaft gears must align with the corresponding notches on the rear timing belt cover.
10. Install the J 42069-1 and the J 42069-2 Camshaft Locking Tools to the camshaft gears. If the J 42069-1 or the J 42069-2 Camshaft Locking Tools do not fit into the teeth of the camshaft gears, it may be necessary to loosen the relevant timing belt idler pulley and turn the eccentric until the J 42069-1 or the J 42069-2 can be inserted.
11. Loosen the timing belt tensioner and idler pulleys, remove the timing belt.
Important: Do not move the crankshaft while the timing belt is removed.
Do not move the camshaft while the timing belt is removed.
Do not remove the locking tools, J 42069-1 and the J 42069-2 Camshaft Locking Tools, while the belt is removed.
Installation Procedure
Tools Required
- J 42069 Timing Belt Alignment Kit
- J 42098 Crank Hub Torx Socket
Important: Guide marks are printed on the timing belt to aid in installation. If these marks are not identifiable, install a new belt.
Arrows are printed on the timing belt indicating the required direction of travel. When installing the timing belt, ensure the arrows are traveling in engine rotational direction (clockwise).
Install the timing belt with the engine at room temperature and use care so as not to crimp the belt.
1. Remove the J 42069-10 Crankshaft Locking Tool.
2. Raise and support the vehicle.
3. Start at the crankshaft drive gear and install the timing belt with the double dash (TDC) mark on the belt aligned with the marks on the oil pump and on the belt drive gear.
4. Use the J 42069-30 to pinch the belt to prevent the teeth from jumping.
5. Lower the vehicle.
6. Route the timing belt through the timing belt tensioner.
7. Slip the timing belt through camshaft gears 1 and 2 simultaneously, ensuring the dash marks on the timing belt align with the arks on the camshaft gears and the notches on the rear timing belt cover.
8. Route the timing belt through the idler pulley for camshaft 1 and 2.
9. Route the timing belt through the idler pulley for camshaft 3 and 4.
10. Slip the timing belt through camshaft gears 3 and 4 simultaneously, ensuring the dash marks on the timing belt align with the marks on the camshaft gears and the notches on the rear timing belt cover.
11. Measure the timing belt deflection between camshaft gear number 4 and the idler pulley for camshafts 3 and 4, the deflection must be no more than 1 cm (0.4 in).
12. If timing belt deflection adjustment is necessary:
12.1. Turn the timing belt idler pulley eccentric for camshaft 3 and 4 COUNTERCLOCKWISE, with J 42069-40, until the high point of the eccentric is in approximately the 12 o'clock position.
12.2. Tighten the idler pulley locking bolt, while holding the eccentric with J 42069-40, until snug. The idler pulley bolt will be tightened to specification after all final adjustments are made.
13. Apply additional tension to the timing belt, at the idler pulley for camshafts 1 and 2, by turning the high point of the eccentric to approximately the 9 o'clock position. Then, tighten the idler pulley locking bolt, while holding the eccentric with J 42069-40, until snug. The idler pulley bolt will be tightened to specifications after all final adjustments are made.
14. Set the initial timing belt tension:
14.1. Turn the tensioner eccentric COUNTERCLOCKWISE to full stop, then, turn the eccentric back until the reference mark is 1 mm (0.003 in) over the flange.
14.2. Tighten the timing belt tensioner locking nut until snug, the locking nut will be tightened to specifications after all final adjustments are made.
15. Inspect the alignment marks on the timing belt to ensure that they are aligned with the appropriate reference points on the camshaft gears, the rear timing belt cover and on the oil pump housing.
16. Remove the J 42069-30, the J42069-1 and the J 42069-2 locking tools from the engine.
17. Rotate the engine, with J 42098 Crank Hub Torx Socket, in the clockwise direction two revolutions stopping at 60 degrees BTDC.
18. Install the J 42069-10 Crankshaft Locking Tool to the crankshaft drive gear with the knurled bolt.
19. Turn the crankshaft until the lever of the J 42069-10 Crankshaft Locking Tool firmly contacts the water pump pulley flange.
20. Secure the moveable lever of the tool to the water pump pulley flange.
Important: The alignment marks on the timing belt will no longer align with the marks on the camshaft gears after one of more engine revolutions.
21. Inspect the alignment of the reference marks on the camshaft gears with the notches on the rear timing belt cover, as well as, the mark on the crankshaft drive gear and oil pump housing.
22. Use the J 42069-20 Checking Gauge to inspect the alignment of camshaft gears 3 & 4.
23. Use the J 42069-20 Checking Gauge to inspect the alignment of camshaft gears 1 & 2.
Important: The reference marks on both sets of the camshaft gears must match exactly with the marks on the J 42069-20 Checking Gauge. If timing belt adjustment is necessary, always set the adjustment for camshaft 3 and 4 first.
24. If timing belt adjustment IS required, refer to Timing Belt Timing Procedure.
25. If timing belt adjustment IS NOT required, set the final timing belt tension:
25.1. Loosen the timing belt tensioner eccentric locking nut.
25.2. Turn the eccentric counterclockwise to full stop, then back until the reference mark is 2-4 mm (0.078-0.157 in) ABOVE the reference mark on the flange.
Notice:
Tighten
Tighten both idler pulley bolts to 40 Nm (30 lb ft).
26. Hold the timing belt idler pulley eccentrics in place for camshafts 1 & 2 and 3 & 4 with the J 42069-40 Adjustment Wrench.
Tighten
Tighten both idler pulley bolts to 40 Nm (30 lb ft).
27. Inspect the highpoints of the timing belt tensioner eccentrics. The idler pulley eccentric high point for camshafts 3 and 4 will be in approximately the 12 o'clock position. The idler pulley eccentric high point for camshaft 1 and 2 will be in approximately the 9 o'clock position.
28. Remove the J 42069-20 Checking Gauge and the J 42069-10 Crankshaft Locking Tool.
29. For final inspection, rotate the engine in the clockwise direction two revolutions until reaching 60 degrees BTDC.
30. Install the J 42069-10 Crankshaft Locking Tool to the crankshaft drive gear with the knurled bolt.
31. Turn the crankshaft until the lever of the J 42069-10 Crankshaft Locking Tool firmly contacts the water pump pulley flange.
32. Secure the moveable lever of the tool to the water pump pulley flange.
33. Inspect the alignment of the reference marks on the camshaft gears with the notches on the rear timing belt cover, as well as, the mark on the crankshaft gear and the mark on the oil pump housing.
34. Use the J 42069-20 Check Gauge to inspect the alignment of camshaft gears 3 and 4.
35. Use the J 42069-20 Checking Gauge to inspect the alignment of the camshaft gears 1 and 2.
36. If the reference marks on the camshaft gears do not match exactly, adjust the timing belt. Refer to Timing Belt Timing Procedure.
37. If further timing belt adjustment IS NOT necessary, continue with reassembly.
38. Ensure all tools are removed from the engine.
39. Install the harmonic balancer to the crankshaft drive gear.
Tighten
Tighten the harmonic balancer bolts to 20 Nm (15 lb ft).
40. Install the timing belt cover.
41. Install the intake air resonator.
42. Reconnect the negative battery cable.
43. Reprogram the applicable accessories.