Radio Control Operations

U1L, UW7, UTO, UP2

Steering Wheel Controls:

ON/OFF - Press the volume knob for ON and OFF.

VOLUME - Volume is controlled with this knob: Clockwise = louder, counter-clockwise = less volume. Volume knob is designed to rotate infinitely.

BALANCE - Lightly press the balance control knob, rotating it clockwise moves the sound to the right speakers; rotating it counter-clockwise move the sound to the left speakers.

FADE - Lightly press the fade control dial, rotating it clockwise moves the sound to the front speakers; rotating it counter-clockwise moves the sound to the rear speakers.

DSPL - Press the DSPL button will recall time of day.

TUNE-SEEK - Press TUNE/SEEK button until you hear a chime to activate the radio to tune to the next higher or lower frequency. If the button is held down for more than two seconds after chime is heard the radio will go in tune fast mode. Release the button when you want to stay at a radio station.

AM - Press the AM button, radio will change to the AM band.

FM1-2 - Press the FM1-2 button to select between FM1 band and FM2 band.

SCAN - Press the SCAN button, the SCAN indicator in the display will light and the radio will light the next station and stay there for a few seconds. Then it will go to the next station and stay there for a few seconds. Then it will go to the next station and pause, and so on. To stop it, press SCAN again.

CLOCK - To set the clock, press and hold the H or M button until it begins to change and then let up as it gets close to the correct time. NOTE: There will be an initial 2-second delay before the clock goes into time-set mode. The clock will stay on the display continuously.

TIME OF DAY - The time of day is maintained by a real time clock internal to the Body Control Module (PZM). This time of day is broadcast as a Class 2 message over the serial data bus. The radio receives this data and displays it on the front panel. Changing the time of day is accomplished through the "hour" and "minute" buttons on the front of the radio. These button presses are translated by the radio which then sends a Class 2 message to the PZM requesting a change in the time. The radio itself does not maintain the time.

PRESET STATIONS - The six buttons let you return to favorite stations. You can set pushbuttons for up to 18 stations (6 AM, 6 FM1 and 6 FM2). Select the band that you want, tune to desired station, press and hold one of the six buttons that you want station set to until you hear a chime and the display channel number and audio returns. Holding button for longer than 2 seconds will activate fast seek mode.

PSCAN - Any station already set up on the preset buttons can be sampled using PSCAN (Preset Scan). Press the SCAN button and hold for 2-3 seconds or until the display shows PSCAN. It will SCAN each of the presets and stop for a few seconds. The tuner will continue scanning until you press scan again. PSCAN will be displayed whenever the tuner is in PSCAN mode.

BASS AND TREBLE - Lightly press the BASS or TREBLE knob, rotating the knob clockwise will increase response. Rotating the knob counter-clockwise will decrease response. There is a center detent position.

BAL - Press this button so it extends. Turn the BAL knob to move the sound to the left or right speakers. The middle position is a detent and balances the speakers. Turn the knob clockwise to adjust sound to the right speakers and counter-clockwise for the left speakers.

FADE - Press this button so it extends. Turn the FADE knob to move the sound to the front or rear speakers. The middle position is a detent and balances the speakers. Turn the knob clockwise to adjust sound to the front speakers and counter-clockwise for the rear speakers.

DSP - The Digital Signal Processing (DSP) feature allows you to tailor the equalization to the type of music or voice heard on the radio, cassette tape and compact disc players. Press this button to go through the four equalization settings of TALK, DRIVER SEAT, LIVE and AUDITORIUM. The words will appear on the display each time the button is pressed. DSP will also appear on the display when in this mode. Press OFF on the DSP button to turn DSP off.

LEVEL - Press the plus or minus symbol on this button to adjust the amount of affect desired when in DSP mode.

STEERING WHEEL CONTROLS - In vehicles with Steering Wheel Controls (SWC), Pressing the VOLUME control will increase or decrease the volume. Pressing the SELECT control will toggle through the presets 1 thru 6 in AM, FM1, and FM2 depending which band is currently being used.