Console Replacement - With UV8
REMOVAL PROCEDURECAUTION: Refer to SIR Handling Caution in Service Precautions.
1. Disable air bag system. Refer to Disabling the SIR System in Restraint Systems.
2. Set the parking brake.
3. Remove the left console trim panel.
4. Remove the right console trim panel.
5. Remove the console center trim plate.
6. Remove the IP center compartment.
7. Remove the left knee bolster.
8. Remove the right knee bolster.
9. Disconnect the transaxle range selector cable terminal from the shift lever pin.
10. Pull the lock release and remove the transaxle shift cable from the console.
11. Remove the console tray (2).
12. Remove the console tray insert from the console tray (2).
13. Remove the interface card from the console tray insert.
14. Disconnect the interface card electrical connector.
15. Remove the rear HVAC control.
16. Remove the center console endcap fasteners (1,2).
17. Remove the center console endcap (3).
18. Disconnect the coaxial cable from the coil cord.
19. Remove the cellular phone wiring from the center console.
20. Remove the 4 console fasteners (1,2) to the IP.
21. Adjust the front seats rearward.
22. Remove the 2 front console to floor fasteners (3).
23. Adjust the front seats forward.
24. Remove the 2 rear console to floor fasteners (4).
25. Move the console rearward, in order to access the center console electrical connectors.
26. Disconnect the center console electrical connectors.
27. Remove the center console.
INSTALLATION PROCEDURE
1. Install the front floor console to the vehicle.
2. Route the cellular phone wiring through the center console to the tray insert area.
3. Connect the coaxial cable to the coil cord.
4. Connect the interface card electrical connector.
5. Install the center console endcap (3).
6. Install the center console endcap fasteners (1,2).
7. Tighten the fasteners (1,2) fully driven, seated, but not stripped.
8. Install the auxiliary HVAC control.
NOTE: Refer to Fastener Notice in Service Precautions.
9. Install the interface card to the console tray insert.
Tighten
Tighten the fasteners to 1.6 N.m (14 lb in).
10. Install the console tray insert to the console tray (2).
11. Connect the center console electrical connectors.
12. Align the locating pins on the floor console to the IP.
13. Install the 2 upper console to IP fasteners (1).
Tighten
Tighten the fasteners (1) to 9 N.m (80 lb in).
14. Install the 2 lower console to IP fasteners (2).
Tighten
Tighten the fasteners (2) to 9 N.m (80 lb in).
15. Adjust the front seats to the forward position.
16. Install the 2 rear console to floor fasteners (4).
Tighten
Tighten the fasteners (4) to 9 N.m (80 lb in).
17. Adjust the front seats to the rear position.
18. Install the 2 front console to floor fasteners (3).
Tighten
Tighten the fasteners (3) to 9 N.m (80 lb in).
19. Slide the transaxle range selector cable fully into the console until it snaps into place.
20. Connect the transaxle range selector cable terminal to the shift lever pin.
21. Install the IP center storage compartment.
22. Install the console center trim plate.
23. Install the right knee bolster.
24. Install the left knee bolster.
25. Install both the left and the right console trim plates.
26. Enable the SIR system. Refer to Enabling the SIR System in Restraint Systems.
"For the description of RPO Code(s) shown in this article or any of the images therein, refer to the RPO Code List found at the Vehicle/Application and ID." RPO Codes