Operation CHARM: Car repair manuals for everyone.

Seat Cushion Frame Replacement - Front



Seat Cushion Frame Replacement - Front

Removal Procedure





1. With the aid from an assistant, remove the seat assembly. Refer to Seat Replacement - Bucket (Seat Replacement - Bucket) .
2. Remove the seat back frame. Refer to Seat Back Frame Replacement - Front (Seat Back Frame Replacement - Front) .
3. Disconnect the electrical connectors (4) if equipped with the heated seats (KA1) or lumbar seats (AL2).
4. Disconnect the three hog rings at the rear edge of the seat cushion.




5. Remove the front and rear outer finish panel fasteners (1).
6. Partially remove the outer finish panel.
7. Disconnect the electrical connectors.
8. Remove the outer finish panel.
9. Disengage the J-channel at the bottom of the seat cushion perimeter.




10. Remove the seat cushion cover (2) and pad (3) from the seat cushion frame.




11. Disengage the memory seat module (3) from the seat cushion pad support wires.




12. Push the seat switch electrical connectors (1,3) through the seat cushion frame (2).
13. Disengage the heated seat relay connector from the seat cushion frame.




14. Remove the four fasteners securing the seat cushion frame to the adjuster assembly.
15. Remove the seat cushion frame from the adjuster assembly.




16. Remove the seat back cushion outer recliner latch assembly fasteners (1).
17. Disengage the two vertical drive cables from the recliner assembly.
18. Remove the forward front seat frame link rivet in order to remove the seat back recliner adjuster assembly.
19. Remove the seat back recliner adjuster assembly (2) from the seat cushion frame and transfer to the new seat frame.
20. Disengage the seat cushion pad support wires from the seat cushion frame.
21. Remove the support wires and transfer to the new seat frame.

Caution: Eye protection must be worn when drilling rivets to reduce the chance of personal injury.

22. Remove the seat adjuster motor bracket rivets.
23. Remove the seat vertical adjuster motor assembly and transfer to the new seat cushion frame.



Installation Procedure





1. Install the seat adjuster vertical motor assembly to the new seat cushion frame.
2. Install new rivets (3) in order to secure the motor assembly to the new seat cushion frame.
3. Install the seat cushion pad support wires to the new seat cushion frame.
4. Position the seat back recliner adjuster assembly to the new seat frame.
5. Secure the forward rivets for the adjuster assembly through the seat frame.





Notice: Refer to Fastener Notice in Cautions and Notices.

6. Install the two bolts (1) in order to secure the recliner hinge (2) to the seat cushion frame.

Tighten the bolts to 24 N.m (18 lb ft).

7. Using a suitable pair of pliers, squeeze the oblong connector and secure the vertical cables to the adjuster assembly.
8. Ensure the connectors are secure.




9. Position the seat cushion frame to the adjuster assembly.

Notice: Refer to Fastener Notice in Cautions and Notices.

10. Install all four seat frame to adjuster assembly bolts.

Tighten the four bolts to 41 N.m (30 lb ft).


Notice: Note the correct routing of the electrical wiring. Failure to reinstall the wiring properly could result in damage to the wiring.





11. Position the seat switch electrical connectors (1,3) through the seat cushion frame (2).




12. Using the seat cushion frame support wires, attach the memory seat module (3) at locations (1,4).
13. Place the cover and pad over the seat back frame recliner hinges.
14. Position the cover and pad to the seat cushion frame.
15. Ensure the seat belt buckle (2) is positioned through the guide loop on the cover.




16. Guide the electrical connectors (4) through the seat cushion cover (1), if equipped with heated or lumbar seats.
17. Connect the three hog rings at the rear of the seat cushion in order to secure the bottom of the cover.
18. Connect the J-channel around the perimeter of the seat cushion frame.




19. Partially install the outer finish panel (1).
20. Connect the electrical connectors for the seat switches.
21. Install the outer finish panel.
22. Ensue the outer finish panel is located (3) into the retainer clip (2) on the seat cushion frame.

Notice: Refer to Fastener Notice in Cautions and Notices.

23. Install the outer finish panel fasteners.

Tighten the fasteners to 2 N.m (18 lb in).





24. Install the seat back frame (2). Refer to Seat Back Frame Replacement - Front (Seat Back Frame Replacement - Front) .
25. With the aid from an assistant, install the seat assembly. Refer to Seat Replacement - Bucket (Seat Replacement - Bucket) .
26. Reposition the seat assembly.