Exhaust System: Service and Repair

Exhaust System Replacement

Removal Procedure





Servicing of the catalytic converter or pipe requires the replacement of the exhaust system as a complete one-piece unit.

Caution: Refer to Exhaust Service Caution in Service Precautions.

Caution: Refer to Protective Goggles and Gloves Caution in Service Precautions.

1. Raise and support the vehicle. Refer to Vehicle Lifting.
2. Remove the 4 bolts securing the oxygen sensor wiring harness heat shield to the floor panel.
3. Remove the oxygen sensor wiring harness heat shield from the floor panel.
4. Disconnect the heated oxygen sensor at the pigtail.
5. Remove the heated oxygen sensor if replacement is necessary.





6. Remove the 4 bolts securing the front floor panel tunnel brace to the floor panel.
7. Remove the front floor panel tunnel brace from the floor panel.
8. Remove the 4 bolts securing the rear floor panel tunnel brace to the floor panel.
9. Remove the rear floor panel tunnel brace from the floor panel.





10. Remove the 4 nuts securing the catalytic converter to the rear exhaust manifold pipe.
11. Remove the catalytic converter gasket. Do not reuse the gasket.
12. Suitably support the exhaust system.





13. Using a pry bar, bend the front body support brackets open, enough to allow the front hangers to be removed.
14. Remove the front exhaust hangers from both the front body support brackets and the front exhaust pipe hanger rods.





15. Apply a suitable lubricant to the body support brackets (1) in order to ease the removal of the intermediate exhaust hangers (2).
16. Pull outward on the intermediate exhaust hangers (2) in order to remove them from the exhaust pipe hanger rods (3).
17. Pull inward on the intermediate exhaust hangers (2) in order to remove them from the body support brackets (1).





18. Apply a suitable lubricant to both the body support brackets (1) and the tail pipe hanger rods (3) in order to ease the removal of the tail pipe hangers (2).
19. Pull outward on the tail pipe hangers (2) in order to remove them from the tail pipe hanger rods (3)
20. Pull inward on the tail pipe hangers (2) in order to remove them from the body support brackets (1).





21. With the aid of an assistant, Lower the exhaust system.

Installation Procedure





Notice: Refer to Exhaust System Inspection Notice in Service Precautions.

1. Place a NEW catalytic converter gasket over the catalytic converter studs.

Notice: Refer to Flex Decoupler Notice in Service Precautions.

2. With the aid of an assistant, raise the exhaust system into position, aligning the catalytic converter with the rear exhaust manifold pipe.
3. Finger tighten the four nuts to the catalytic converter studs.





4. Apply a soapy solution to both the body support brackets (1), the tail pipe hanger rods (3), and the inner diameter of the tail pipe hangers (2) in order to ease the installation of the hangers (2).
5. Press the tail pipe hangers (2) over the body support brackets (1).
6. Press the tail pipe hangers (2) over the tail pipe hanger rods (3).





7. Apply a soapy solution to the body support brackets (1) and the inner diameter of the intermediate exhaust hangers (2) in order to ease the installation of the hangers (2).
8. Press the intermediate exhaust hangers (2) over the body support brackets (1).
9. Press the intermediate exhaust hangers (2) over the exhaust pipe hanger rods (3).





10. Place the front exhaust hangers under the front exhaust pipe hanger rods. _
11. Place the front exhaust hangers over the front body support brackets.

Important: Ensure that the gap (1) between the body and the front body support brackets do not exceed 6 mm (0.23 in).

12. Using a pry bar, bend the front body support brackets closed, securing the front exhaust hangers to the front body support brackets.

Notice: Refer to Fastener Notice in Service Precautions.

13. Tighten the 4 catalytic converter nuts previously installed in step 3.
^ Tighten the catalytic converter nuts to 25 Nm (18 ft. lbs.).
14. Install the heated oxygen sensor.





15. Position the front floor panel tunnel brace to the floor panel.
16. Install the 4 bolts securing the front floor panel tunnel brace to the floor panel.
17. Position the rear floor panel tunnel brace to the floor panel.
18. Install the 4 bolts securing the rear floor panel tunnel brace to the floor panel.
^ Tighten the floor panel tunnel brace bolts to 24 Nm (18 ft. lbs.).





19. Position the oxygen sensor wiring harness heat shield to the floor panel.
20. Align the holes in the oxygen sensor wiring harness heat shield with the threaded holes in the floor panel.
21. Install the 4 bolts securing the oxygen sensor wiring harness heat shield to the floor panel.
^ Tighten the oxygen sensor wiring harness heat shield bolts to 6 Nm (53 inch lbs.).
22. Lower the vehicle.