Scan Tool Data Definitions

SCAN TOOL DATA DEFINITIONS

Battery Voltage: Displays 0 to 30 volts. The voltage measured between the module's battery positive voltage circuit and ground circuit.

Calibrate Module: to calibrate module, follow on screen instructions

Courtesy Lamp 1,2 With RPO Code dim: ON or OFF. Commands the courtesy lamps ON or OFF using the theater dimming function.

Courtesy Lamp 1,2 With Out RPO Code dim: Displays ON or OFF. Commands the courtesy lamps ON or OFF. Does not use the theater dimming function.

Courtesy Lamp Switch: ON or OFF. Indicates the status of the courtesy lamp switch input.

Daytime Running Lamp: ON or OFF. The commanded state of the DRL relay.

Daytime Running Lamps: ON or OFF. Commands the daytime running lamp relay ON or OFF.

Dimming Pot A/D: 0-255 counts. Display indicates the level of incandescent dimming.

Driver Door Jamb Sw.: ON or OFF. The status of the driver door jamb switch.

Flash to Pass Switch: ON or OFF. Indicates the status of the flash to pass switch input.

Front Fog Lamp: ON or OFF. Displays the commanded state of the front fog lamp relay.

Front Fog Lamps: ON or OFF. Commands the front fog lamp relay ON or OFF.

Front Fog Lamp Switch: ON or OFF. Indicates the status of the front fog lamp switch input.

Front Sensor: Displays 0-100%. Indicates the position of the front axle sensor in relationship to the zero point established during the calibration procedure.

Hazard Lamp Switch: ON or OFF. Indicates the status of the hazard switch input.

Head Lamp Switch: ON or OFF. Indicates the status of the headlamp switch input.

High Beam - Flash to Pass: ON or OFF. Displays the commanded state of the high beam - flash to pass relay.

High Beam - Flash to Pa: ON or OFF. Commands the high beam relay ON or OFF.

High/Low Beam Relay: ON or OFF. Displays the commanded state of the headlamp relay.

High/Low Beam Relay: ON or OFF. Commands the headlamp relay ON or OFF.

Inadvertent Power Input: ON or OFF. Display indicates the state of the inadvertent power.

Inadvertent Power Relay: ON or OFF. Display indicates the commanded state of the inadvertent power relay.

Incandescent Dimming: ON or OFF. Display indicates the state of the incandescent lamp ground circuit.

Incandescent Dimming: the percentage of dimming control of the dash integration module output.

Left Rear Door Jamb Sw.: ON or OFF. Indicates the status of the left rear door jamb switch.

Left Turn Signal: ON or OFF. Indicates the status of the left turn signal indicator.

Lights On With Wipers: ON or OFF. Indicates the status of the lights on with wipers input.

Lighting for Theft: ON or OFF. Commands the theft lighting ON or OFF.

Low Beam Input: 0-25.5 volts. Indicates the voltage at the low beam HID bulb.

Overhead Lamps Output: ON or OFF. Indicates the status of the overhead lamps.

Park Brake Switch: ON or OFF. Indicates the status of the park brake switch input.

Park Lamp Switch: ON or OFF. Indicates the status of the park lamp switch input.

Park Lamp Relay: ON or OFF. Displays the commanded state of the park lamp relay.

Parking Lamps Relay: ON or OFF. Commands the park lamp relay ON or OFF.

Pas. Door Jamb Sw.: ON or OFF. Indicates the status of the passenger door jamb switch.

Position Lamp Relay: ON or OFF. Displays the commanded state of the position lamp relay.

Rear Fog Lamp Relay: ON or OFF. Displays the commanded state of the rear fog lamp relay.

Rear Fog Lamp Relay: ON or OFF. Commands the rear fog lamp relay ON or OFF.

Rear Fog Lamp Switch: ON or OFF. Indicates the status of the rear fog lamp switch input.

Reverse Lamp Relay: ON or OFF. Displays the commanded state of the reverse lamp relay.

Reverse Lamp Relay: ON or OFF. Commands the reverse lamp relay ON or OFF.

Rear Sensor: Displays 0-100%. Indicates the position of the rear axle sensor in relationship to the zero point established during the calibration procedure.

Right Turn Signal: ON or OFF. Indicates the status of the right turn signal indicator.

Rt Rear Door Jamb Sw.: ON or OFF. Indicates the status of the right rear door jamb switch.

Stepper Motor Position: 0-255 Counts. Indicates the position of the headlamp leveling stepper motor.

Stepper Motor Test: the automatic headlamp leveling steeper motor to the full up or full down position.

Stoplamp Pedal Switch: the position of the stop lamp pedal switch input to the engine control module.

Switch Dimming: the percentage of dimming control of the appropriate door control module output.

Theft Lighting: ON or OFF. Indicates the status of the theft lighting input signal.

Transmission Range: Displays PARK/REVERSE/NEUTRAL/DRIVE4/DRIVE3/DRIVE2/DRIVE1.Indicates the position of the automatic transmission shift lever.

Twilight Switch: DAY or NIGHT. Indicates the status of the twilight photocell input.