Reveal Molding Replacement - Rear Door Window

Reveal Molding Replacement - Rear Door Window

Tools Required

J 38778 Door Trim Pad and Garnish Clip Remover


Removal Procedure

1. Position the window fully downward.
2. Remove the trim panel. Refer to Trim Panel Replacement - Side Rear Door (Standard) (Trim Panel Replacement - Side Rear Door (Standard))Trim Panel Replacement - Side Rear Door (WC2, WC8) (Trim Panel Replacement - Side Rear Door (WC2, WC8)) .
3. Remove the door module. Refer to Door Control Module Replacement
4. Remove the water deflector. Refer to Water Deflector Replacement - Rear Door (Service and Repair) .
5. Remove the garnish molding. Refer to Garnish Molding Replacement - Rear Door Frame (Service and Repair) .
6. Remove the inner window belt sealing strip. Refer to Sealing Strip Replacement - Rear Door Window Belt Inner (Service and Repair) .
7. Remove the window. Refer to Window Replacement - Rear Door (Standard Door) (Window Replacement - Rear Door (Standard Door))Window Replacement - Rear Door (RPO WC2 and WC8) (Window Replacement - Rear Door (RPO WC2 and WC8))Window Replacement - Rear Door (RPO WC2 and WC8 w/ Stationary Window) (Window Replacement - Rear Door (RPO WC2 and WC8 w/ Stationary Window)) .
8. Remove the rear door stationary window/division channel. Refer to Window/Division Channel - Rear Door Stationary (Window/Division Channel - Rear Door Stationary) .




9. Remove the seven screws attaching the reveal molding to the door.
10. Insert a thin, flat-bladed tool between the applique (5) and the door pillar and cut the foam tape. Work from the top downward until the tape is separated.
11. Use the J 38778 to release the push pins securing the reveal molding to the door.
12. Perform the following to remove the reveal molding:

1. Pull outward on the scalp section (2), away from the door header.
2. Grip the inner and outer sides of the belt section (3), and pull upward to release the reveal molding from the door flange (6).




Installation Procedure


Important: If the old molding is to be reused, the foam tape must be replaced as outlined in steps 1 through 4. A new molding from GMSPO will have new tape installed.






1. Mark the location of the old tape strip on the molding applique with a scribe.
2. Remove all of the tape residue from the door pillar and the molding applique (1).
Use a isopropyl alcohol dampened cloth in order to remove the old tape residue.
3. Install new foam tape to the molding applique (1). Align the new tape with the scribe marks made previously.
4. Wrap the clear plastic release liner tab to the outside of the molding applique (1).
5. Secure the release liner tab in place with a small piece of masking tape (2).
6. Ensure the door is properly aligned prior to installing the reveal molding. Refer to Door Adjustment (Adjustments) .





Important: The following must be maintained when the belt section is positioned to the flange:


* The belt molding blade is engaged into the flange notch (4).

* The lace (7) is compressed inboard and constant.



7. Position the front edge of the belt section (3) to the front edge of the door.
8. Work the reveal moldings belt section (3) into the door flange (6) by pushing downward from front to rear.
9. Press the push pins into the door pillar.
10. Install the alignment screw (1) to the door header.

Notice: Refer to Fastener Notice in Cautions and Notices.

11. Working rearward, install the remaining screws.

Tighten the screws to 1.3 N.m (12 lb in).





12. Remove the release liner from the tape.
13. Press firmly onto the applique (1) to adhere the tape to the door pillar.
14. Install the stationary window/division channel. Refer to Window/Division Channel - Rear Door Stationary (Window/Division Channel - Rear Door Stationary) .
15. Install the window. Refer to Window Replacement - Rear Door (Standard Door) (Window Replacement - Rear Door (Standard Door))Window Replacement - Rear Door (RPO WC2 and WC8) (Window Replacement - Rear Door (RPO WC2 and WC8))Window Replacement - Rear Door (RPO WC2 and WC8 w/ Stationary Window) (Window Replacement - Rear Door (RPO WC2 and WC8 w/ Stationary Window)) .
16. Install the inner window belt sealing strip. Refer to Sealing Strip Replacement - Rear Door Window Belt Inner (Service and Repair) .
17. Install the garnish molding. Refer to Garnish Molding Replacement - Rear Door Frame (Service and Repair) .
18. Install the water deflector. Refer to Water Deflector Replacement - Rear Door (Service and Repair) .
19. Install the door module. Refer to Door Control Module Replacement
20. Install the trim panel. Refer to Trim Panel Replacement - Side Rear Door (Standard) (Trim Panel Replacement - Side Rear Door (Standard))Trim Panel Replacement - Side Rear Door (WC2, WC8) (Trim Panel Replacement - Side Rear Door (WC2, WC8)) .