P0103
DTC P0102 or P0103
Diagnostic Instructions
* Perform the Diagnostic System Check - Vehicle prior to using this diagnostic procedure. Initial Inspection and Diagnostic Overview
* Review Strategy Based Diagnosis for an overview of the diagnostic approach.
* Diagnostic Procedure Instructions provides an overview of each diagnostic category.
DTC Descriptors
DTC P0102
- Mass Air Flow (MAF) Sensor Circuit Low Frequency
DTC P0103
- Mass Air Flow (MAF) Sensor Circuit High Frequency
Diagnostic Fault Information
Typical Scan Tool Data
Circuit/System Description
The mass air flow (MAF) sensor is integrated with the intake air temperature (IAT) sensor. The MAF sensor is an air flow meter that measures the amount of air entering the engine. The engine control module (ECM) uses the MAF sensor signal to provide the correct fuel delivery for all engine speeds and loads. A small quantity of air entering the engine indicates a deceleration or idle condition. A large quantity of air entering the engine indicates an acceleration or high load condition. The MAF/IAT sensor has the following circuits:
* An ignition 1 voltage circuit
* A ground circuit
* A MAF sensor signal circuit
* An IAT sensor signal circuit
* A low reference circuit
The ECM applies 5 volts to the MAF sensor on the MAF sensor signal circuit. The sensor uses the voltage to produce a frequency based on the inlet air flow through the sensor bore. The frequency varies within a range of near 2,000 Hertz at idle to near 9,500 Hertz at maximum engine load.
Conditions for Running the DTC
* The engine is running for more than 1 second.
* The engine speed is more than 300 RPM.
* The ignition 1 signal is more than 8 volts.
* The above conditions are met for more than 1 second.
* This DTC runs continuously within the enabling conditions.
Conditions for Setting the DTC
DTC P0102
The ECM detects that the MAF Sensor parameter is less than 10 Hz for more than 5 seconds.
DTC P0103
The ECM detects that the MAF Sensor parameter is more than 14,500 Hz for more than 5 seconds.
Action Taken When the DTC Sets
DTCs P0102 and P0103 are Type B DTCs.
Conditions for Clearing the MIL/DTC
DTCs P0102 and P0103 are Type B DTCs.
Diagnostic Aids
* A wide open throttle (WOT) acceleration from a stop should cause the MAF sensor parameter on the scan tool to increase rapidly. This increase should be from 6-10 g/s at idle to 380 g/s or more at the time of the 1-2 shift.
* Verify that any electrical aftermarket devices are properly connected and grounded. Refer to Checking Aftermarket Accessories Diagnostic Aids. Component Tests and General Diagnostics
Circuit/System Verification
Verify the integrity of the air induction system by inspecting for the following conditions:
* Damaged components
* Loose or improper installation
* An air flow restriction
* Any vacuum leak
* Water intrusion
Circuit/System Testing
1. Ignition OFF, disconnect the harness connector at the MAF/IAT sensor.
2. Ignition OFF, allow sufficient time for the ECM to power down. Test for less than 5 ohms of resistance between the MAF low reference circuit terminal D and ground.
• If greater than the specified range, test the low reference circuit for an open/high resistance. If the circuit tests normal, replace the ECM.
3. Ignition ON, test for 4.8-5.2 volts between the MAF signal circuit terminal A and ground.
• If less than the specified range, test the signal circuit for a short to ground or an open/high resistance. If the circuit tests normal, replace the ECM.
• If greater than the specified range, test the signal circuit for a short to voltage. If the circuit tests normal, replace the ECM.
4. Ignition ON, verify a test lamp illuminates between the ignition circuit 1 terminal C and ground.
• If the test lamp does not illuminate, test the ignition circuit for a short to ground or an open/high resistance.
5. Connect the J 38522 to the vehicle. Refer to Component Testing.
Component Testing
Important: You must perform the Circuit/System Testing before proceeding with the Component Testing.
To determine if the ECM can properly process the MAF sensor frequency signal, connect the J 38522 to the vehicle as follows:
1. Turn OFF the ignition.
2. Connect the battery voltage supply, and ground the black lead.
3. Connect the red lead to the signal circuit terminal A of the MAF sensor.
4. Set the Duty Cycle switch to Normal.
5. Set the Frequency switch to 5 K.
6. Set the Signal switch to 5 V.
7. Start the engine and observe the MAF Sensor parameter for the correct range of 4,950-5,025 Hz.
• If the MAF Sensor parameter is not within the specified range, replace the ECM.
• If the MAF Sensor parameter is within the specified range, replace the MAF sensor.
Repair Instructions
Perform the Diagnostic Repair Verification after completing the diagnostic procedure. Verification Tests
* Mass Airflow Sensor/Intake Air Temperature Sensor Replacement
* Refer to Programming and Relearning for ECM setup and programming Programming and Relearning