P0112
DTC P0112 or P0113
Diagnostic Instructions
* Perform the Diagnostic System Check - Vehicle (Initial Inspection and Diagnostic Overview) prior to using this diagnostic procedure.
* Review Strategy Based Diagnosis (Initial Inspection and Diagnostic Overview) for an overview of the diagnostic approach.
* Diagnostic Procedure Instructions (Initial Inspection and Diagnostic Overview) provides an overview of each diagnostic category.
DTC Descriptors
DTC P0112
- Intake Air Temperature (IAT) Sensor Circuit Low Voltage
DTC P0113
- Intake Air Temperature (IAT) Sensor Circuit High Voltage
Diagnostic Fault Information
Typical Scan Tool Data
Circuit/System Description
The intake air temperature (IAT) sensor is a variable resistor. The IAT sensor has a signal circuit and a low reference circuit. The IAT sensor measures the temperature of the air entering the engine. The engine control module (ECM) supplies 5 volts to the IAT signal circuit, and a ground for the IAT low reference circuit. When the IAT sensor is cold, the sensor resistance is high. When the air temperature increases, the sensor resistance decreases. With high sensor resistance, the ECM detects a high voltage on the IAT signal circuit. With lower sensor resistance, the ECM detects a lower voltage on the IAT signal circuit.
Conditions for Running the DTC
P0112
* DTC P0117, P0118, P0116, P0128, P0500, P0608, or P0609 are not set.
* The engine speed is greater than 1 km/h (1 mph).
* The engine coolant temperature (ECT) sensor is less than 150°C (302°F).
* The engine run time is greater than 10 seconds.
* DTC P0112 runs continuously when the above enable conditions are met.
P0113
* DTC P0101, P0102, P0103, P0117, P0118, P0116, P0128, P0500, P0608, or P0609 are not set.
* The electronic coolant temperature (ECT) sensor is greater than -40°C (-40°F).
* The mass air flow (MAF) sensor is less than 512 g/s.
* The engine run time is greater than 10 seconds.
* DTC P0113 runs continuously when the above enable conditions are met.
Conditions for Setting the DTC
P0112
The IAT sensor is greater than 148°C (298°F) for greater than 5 seconds.
P0113
The IAT sensor is less than -39°C (-38°F) for greater than 5 seconds.
Action Taken When the DTC Sets
DTCs P0112 and P0113 are Type B DTCs.
Conditions for Clearing the MIL/DTC
DTCs P0112 and P0113 are Type B DTCs.
Diagnostic Aids
If the engine is cold, then at ignition ON a properly functioning IAT sensor will gradually increase the scan tool IAT Sensor parameter. This is due to the heat that is generated by the MAF sensor heating elements.
Reference Information
Schematic Reference
Engine Controls Schematics (Electrical Diagrams)
Connector End View Reference
Component Connector End Views (Connector Views)
Electrical Information Reference
* Circuit Testing (Component Tests and General Diagnostics)
* Connector Repairs (Component Tests and General Diagnostics)
* Testing for Intermittent Conditions and Poor Connections (Component Tests and General Diagnostics)
* Wiring Repairs (Component Tests and General Diagnostics)
DTC Type Reference
Powertrain Diagnostic Trouble Code (DTC) Type Definitions (Diagnostic Trouble Code Descriptions)
Scan Tool Reference
Control Module References (Programming and Relearning) for scan tool information
Circuit/System Verification
Important:
* Perform this verification procedure only when the ignition has been OFF for 8 hours or more.
* The IAT will begin to warm up as soon as the ignition key is turned ON
1. Ignition ON, observe the scan tool IAT Sensor, IAT Sensor 2, and ECT Sensor parameters. The readings should be within 15°C (27°F) of each other and also the ambient temperature.
2. Operate the vehicle within the Conditions for Running the DTC. You may also operate the vehicle within the conditions that you observed from the Freeze Frame/Failure Records data.
Circuit/System Testing
1. Ignition OFF, disconnect the MAF/IAT harness connector at the MAF/IAT sensor.
2. Ignition OFF for 90 seconds, test for less than 5 ohms of resistance between the low reference circuit terminal D and ground.
• If greater than the specified range, test the low reference circuit for an open/high resistance. If the circuit tests normal, replace the ECM.
3. Ignition ON, verify the scan tool IAT Sensor parameter is less than -39°C (-38°F).
• If greater than the specified range, test the signal circuit terminal E for a short to ground. If the circuit tests normal, replace the ECM.
Important: If the 3A fuse in the jumper wire opens, the signal circuit is shorted to a voltage and the sensor may be damaged.
4. Install a 3A fused jumper wire between the signal circuit terminal E and a ground. Verify the scan tool IAT Sensor parameter is greater than 149°C (300°F).
• If less than the specified range, test the signal circuit for a short to voltage or an open/high resistance. If the circuit tests normal, replace the ECM.
5. If all circuits test normal, test or replace the MAF/IAT sensor.
Component Testing
Compare the IAT sensor resistance to the values listed in the Temperature vs. Resistance table. Refer to Temperature Versus Resistance (Temperature Versus Resistance) .
Repair Instructions
Perform the Diagnostic Repair Verification (Verification Tests) after completing the diagnostic procedure.
* Mass Airflow Sensor/Intake Air Temperature Sensor Replacement (Service and Repair)
* Control Module References (Programming and Relearning) for ECM replacement, setup, and programming