P0121
DTC P0068 or P0121
Diagnostic Instructions
* Perform the Diagnostic System Check - Vehicle (Initial Inspection and Diagnostic Overview) prior to using this diagnostic procedure.
* Review Strategy Based Diagnosis (Initial Inspection and Diagnostic Overview) for an overview of the diagnostic approach.
* Diagnostic Procedure Instructions (Initial Inspection and Diagnostic Overview) provides an overview of each diagnostic category.
DTC Descriptors
DTC P0068
- Throttle Body Airflow Performance
DTC P0121
- Throttle Position (TP) Sensor Performance
Circuit/System Description
The actual throttle position and airflow rate is compared to an expected throttle position and airflow rate based on engine load. The engine control module (ECM) determines engine load based on inputs from the mass air flow (MAF) sensor and the manifold absolute pressure (MAP) sensor. Further comparisons are done to distinguish if a sensor is at fault, and the respective DTC will set.
The ECM uses the following information to calculate an expected airflow rate:
* The throttle position (TP)
* The barometric pressure (BARO)
* The manifold absolute pressure (MAP)
* The supercharger inlet absolute pressure (SCIAP)
* The intake air temperature (IAT)
* The engine RPM
Conditions for Running the DTC
P0068
* DTCs P0122, P0123, P0220, P0221, P0222, P0223, P0601, P0602, P0603, P0604, P0606, P0607, P060D, P062F, P0641, P0651, P1516, P2101, P2119, P2135, P2176, P2610 are not set.
* The engine is running.
* DTC P0068 runs continuously when the above conditions are met.
P0121
* DTCs P0102, P0103, P0107, P0108, P0112, P0113, P0117, P0118, P0116, P0128, P0122, P0123, P0220, P0221, P0222, P0223, P0335, P0336, P0401, P0405, P0601, P0602, P0603, P0604, P0606, P0607, P060D, P062F, P0641, P0651, P1404, P1516, P2101, P2119, P2135, P2176, P2610 are not set.
* The engine coolant temperature (ECT) is between 70-121°C (158-249°F).
* The engine IAT is between -7 and +60°C (+19 and +140°F).
* The engine is running.
* DTC P0121 runs continuously when the above conditions are met.
Conditions for Setting the DTC
The ECM detects that the airflow rate is greater than the calculated airflow for greater than 0.2 second.
Action Taken When DTC
* DTC P0068 is a Type A DTC.
* DTC P0121 is a Type B DTC.
Conditions for Clearing the MIL/DTC
* DTC P0068 is a Type A DTC.
* DTC P0121 is a Type B DTC.
Reference Information
Schematic Reference
Engine Controls Schematics (Electrical Diagrams)
Connector End View Reference
Component Connector End Views (Connector Views)
Electrical Information Reference
* Circuit Testing (Component Tests and General Diagnostics)
* Connector Repairs (Component Tests and General Diagnostics)
* Testing for Intermittent Conditions and Poor Connections (Component Tests and General Diagnostics)
* Wiring Repairs (Component Tests and General Diagnostics)
Description and Operation Reference
Throttle Actuator Control (TAC) System Description (Throttle Actuator Control (TAC) System Description)
DTC Type Reference
Powertrain Diagnostic Trouble Code (DTC) Type Definitions (Diagnostic Trouble Code Descriptions)
Scan Tool Reference
Control Module References (Programming and Relearning) for scan tool information
Circuit/System Verification
1. Verify that DTCs P0101, P0106, P0120, P012B, or P0220 are not set.
• If any of the DTCs are set, refer to Diagnostic Trouble Code (DTC) List - Vehicle (Diagnostic Trouble Code Descriptions) .
2. Ignition ON, observe the scan tool BARO, MAP, and the SC Inlet Pressure sensor parameters. The readings should be within the range specified for your altitude. Determine the altitude at your current location and refer to Altitude Versus Barometric Pressure (Altitude Versus Barometric Pressure) .
3. Start the engine. The Manifold Absolute Pressure (MAP) and SC Inlet Pressure Sensor parameters should decrease and closely match each other.
• If the MAP sensor parameter does not decrease, refer to DTC P0106 (P0106) .
• If the SC Inlet Pressure Sensor parameter does not decrease, refer to DTC P0128 (P0128) .
4. Operate the vehicle within the Conditions for Running the DTC. You may also operate the vehicle within the conditions that you observed from the Freeze Frame/Failure Records data.
Circuit/System Testing
Important: You must perform the Circuit/System Verification before proceeding with the Circuit/System Testing.
1. Inspect for the following conditions:
* Vacuum hoses for splits, leaks, and improper connections
* Air leaks at throttle body mounting area and intake manifold sealing surfaces
* A supercharger bypass valve that is binding or incorrectly adjusted-Refer to Supercharger Cleaning and Inspection (Overhaul) .
* Inspect throttle body for dirt, debris, and coking. Refer to Throttle Body Inspection and Cleaning (Throttle Body Inspection and Cleaning) .
• If any of the above conditions are found, repair as necessary.
2. Allow the engine to reach operating temperature. Observe the MAP Sensor Voltage parameter with a scan tool. Voltage should be greater than 0.8 volt and less than 4 volts.
• If greater than 4 volts or less than 0.8 volt, refer to DTC P0106 (P0106) .
3. Idle the engine. Observe the MAP Sensor kPa parameter with a scan tool. Increase the engine speed slowly and then back to idle. The MAP sensor kPa should change smoothly and gradually as engine speed is increased and returned to idle.
• If the MAP sensor kPa does not change, refer to DTC P0106 (P0106) .
4. Take a snapshot of the engine data list while performing the actions listed below. The mass airflow (MAF) sensor g/s should change smoothly and gradually as the engine is increased and returned to idle.
1. Idle the engine.
2. Increase the engine speed slowly to 3,000 RPM, then back to idle.
3. Exit from the snapshot and review the data.
4. Observe the Mass Air Flow (MAF) Sensor parameter frame by frame with a scan tool. The MAF sensor g/s should change smoothly and gradually as the engine speed is increased and is returned to idle.
• If the MAF sensor g/s does not change smoothly and gradually as the engine speed is increased and is returned to idle, refer to DTC P0101 or P1101 (P0101) .
5. Ignition ON, slowly depress the accelerator pedal to a WOT position, then slowly release the pedal while comparing the TP Sensor 1 and TP Sensor 2 parameters. The difference between the parameters should be less than 4 percent.
• If TP Sensor 1 and TP Sensor 2 parameters differ more than 4 percent, refer to DTC P0120, P0122, P0123, P0220, P0222, P0223, or P2135 (P0120) .
Caution: Turn OFF the ignition before inserting fingers into the throttle bore. Unexpected movement of the throttle blade could cause personal injury.
6. Ignition OFF, inspect the throttle body for the following conditions:
* Loose or damaged throttle blade
* Broken throttle shaft
* Any throttle body damage
• If any of these conditions exist, replace the throttle body assembly.
Repair Instructions
Perform the Diagnostic Repair Verification (Verification Tests) after completing the diagnostic procedure.
* Air Cleaner Element Replacement (Service and Repair)
* Air Cleaner Outlet Duct Replacement (Air Cleaner Outlet Duct Replacement)
* Mass Airflow Sensor/Intake Air Temperature Sensor Replacement (Service and Repair)
* Replacing Engine Gaskets (Replacing Engine Gaskets)
* Supercharger Inlet Duct Installation (Overhaul)
* Throttle Body Assembly Replacement (Removal and Replacement)
* Control Module References (Programming and Relearning) for ECM replacement, setup, and programming