Operation CHARM: Car repair manuals for everyone.

P0971



DTC P0969, P0970 or P0971

Diagnostic Instructions

* Perform the Diagnostic System Check - Vehicle (Initial Inspection and Diagnostic Overview) prior to using this diagnostic procedure.
* Review Strategy Based Diagnosis (Initial Inspection and Diagnostic Overview) for an overview of the diagnostic approach.
* Diagnostic Procedure Instructions (Initial Inspection and Diagnostic Overview) provides an overview of each diagnostic category.



DTC Descriptors
DTC P0969
- Clutch Pressure Control (PC) Solenoid 3 System Performance

DTC P0970
- Clutch Pressure Control (PC) Solenoid 3 Control Circuit Low Voltage

DTC P0971
- Clutch Pressure Control (PC) Solenoid 3 Control Circuit High Voltage




Diagnostic Fault Information






Typical Scan Tool Data






Circuit/System Description

The clutch pressure control (PC) solenoid 3 is integral to the control solenoid (w/body and TCM) valve assembly and has no serviceable parts. The PC solenoid 3 is a normally high-pressure control solenoid which provides fluid pressure to the BR1 and 456 clutch regulator valve. The TCM controls the solenoid pressure by regulating the exhaust fluid. When the TCM commands the solenoid off, the exhausting fluid is stopped and the BR1 and 456 pressure is high. When commanded on, the clutch PC solenoid 3 regulates the amount of exhausting transmission fluid. Solenoid power is supplied by the TCM through a high side driver (HSD). The HSD protects the circuits and components that the TCM powers. Should the circuit overload the driver will shutdown. After the overload is removed the HSD reset.


Conditions for Running the DTC

* The engine run time is greater than 5 seconds.
* The clutch PC solenoid 3 is commanded ON.



Conditions for Setting the DTC

P0969

The TCM detects an internal electrical performance malfunction of the clutch PC solenoid control circuit and the actual low and reverse/4-5-6 clutch pressure does not equal the commanded low and reverse/4-5-6 clutch pressure for 300 milliseconds.

P0970

The TCM detects an internal low voltage electrical malfunction of the clutch PC solenoid control circuit for 300 milliseconds.

P0971

The TCM detects an internal high voltage electrical malfunction of the clutch PC solenoid control circuit for 300 milliseconds.


Action Taken When the DTC Sets

* DTCs P0969, P0970, and P0971 are Type A DTCs.
* The TCM defaults the transmission to a limited shift pattern utilizing 2 forward gears and reverse based on the default detected.
* The TCM commands maximum line pressure.
* The TCM freezes transmission adaptive functions.



Conditions for Clearing the DTC

DTCs P0969, P0970, and P0971 are Type A DTCs.


Diagnostic Aids

When attempting to set solenoid electrical DTCs, ensure the TCM is warmed up and the transmission is operated in second gear long enough to ensure a 3°C (5°F) increase in TCM substrate temperature. This will place the TCM under the optimal conditions to test solenoid electrical DTCs.


Reference Information
Schematic Reference

Automatic Transmission Controls Schematics (Electrical Diagrams)
Connector End View Reference

Component Connector End Views (Connector Views)
Electrical Information Reference

* Circuit Testing (Component Tests and General Diagnostics)
* Connector Repairs (Component Tests and General Diagnostics)
* Testing for Intermittent Conditions and Poor Connections (Component Tests and General Diagnostics)
* Wiring Repairs (Component Tests and General Diagnostics)

Description and Operation

Transmission Component and System Description (Transmission Component and System Description)
DTC Type Reference

Powertrain Diagnostic Trouble Code (DTC) Type Definitions (Diagnostic Trouble Code Descriptions)
Scan Tool Reference

Control Module References (Programming and Relearning) for scan tool information


Circuit Verification

Perform the following procedure to place the control solenoid (w/body and TCM) valve assembly under the optimal conditions to test solenoid electrical DTCs.

* Ensure the transmission fluid temperature is between 50-80°C (122-176°F).
* Operate the vehicle in second gear long enough to ensure at least a 3°C (5°F) rise in TCM substrate temperature and then operate the vehicle in fourth gear for 5 seconds.



Component Testing

The scan tool data parameter Clutch PC 3 Sol. CKT Status normally displays OK.

If the parameter displays Open/Short to Volts or Short to GND or if the DTC resets, perform the Control Solenoid Valve and Transmission Control Module Assembly Inspection (Control Solenoid Valve and Transmission Control Module Assembly Inspection) and if no concerns are found, replace the control solenoid (w/body and TCM) valve assembly.



Repair Instructions

Perform the Diagnostic Repair Verification (Verification Tests) after completing the diagnostic procedure.

* Replace the control solenoid (w/body and TCM) valve assembly. Refer to Control Module References (Programming and Relearning) for replacement, setup, and programming.
* Perform the Service Fast Learn Adapts (Programming and Relearning) if internal transmission repairs are performed.