Compressor Hose Assembly Replacement
Compressor Hose Assembly Replacement
Tools Required
J 39400-A Halogen Leak Detector
Removal Procedure
1. Recover the refrigerant from the A/C system. Refer to Refrigerant Recovery and Recharging (Refrigerant Recovery and Recharging) .
2. Remove the radiator support. Refer to Radiator Support Replacement (Service and Repair) .
Important: Prior to removal, take note of the A/C compressor hose assembly routing and orientation between the compressor and condenser.
Cap or tape off the open A/C components immediately to prevent system contamination.
3. Remove the A/C compressor hose assembly bolt (1) from the A/C condenser fitting.
4. Disconnect the A/C compressor hose assembly from the A/C condenser fitting.
5. Remove and discard the sealing washer.
6. Cap or tape off the A/C condenser fitting.
7. Disconnect and remove the A/C tube connector from the evaporator outlet tube and A/C compressor hose assembly. Refer to Air Conditioning Line/Tube Connector Removal/Replacement (Air Conditioning Line/Tube Connector Removal/Replacement) .
8. Disconnect the evaporator outlet tube (1) from the A/C compressor hose assembly (2).
9. Cap or tape off the evaporator outlet tube (1).
10. Raise and support the vehicle. Refer to Lifting and Jacking the Vehicle (Service and Repair) .
11. Remove the right front tire and wheel assembly from the vehicle. Refer to Tire and Wheel Removal and Installation (Service and Repair) .
12. Remove the A/C compressor hose assembly to A/C compressor retaining nut (3).
13. Disconnect the A/C compressor hose assembly (2) from the A/C compressor.
14. Remove and discard the sealing washers.
15. Cap or tape off the A/C compressor.
16. Remove the power steering pump. Refer to Power Steering Pump Replacement (RPO LC3) (Service and Repair)Power Steering Pump Replacement (RPO LH2) (Service and Repair) .
17. Lower the vehicle.
18. Remove the A/C compressor hose assembly (2) from the vehicle.
Installation Procedure
1. Install the A/C compressor hose assembly (2) to the vehicle.
2. Install the power steering pump. Refer to Power Steering Pump Replacement (RPO LC3) (Service and Repair)Power Steering Pump Replacement (RPO LH2) (Service and Repair) .
3. Raise and support the vehicle.
4. Remove cap or tape from the A/C compressor.
5. Install new sealing washers onto the compressor hose assembly. Refer to Sealing Washer Replacement (Sealing Washer Replacement) .
6. Connect the A/C compressor hose assembly (2) to the A/C compressor.
Notice: Refer to Fastener Notice .
7. Install the A/C compressor hose assembly to A/C compressor retaining nut (3).
Tighten the nut to 20 N.m (15 lb ft).
8. Install the right front tire and wheel assembly to the vehicle. Refer to Tire and Wheel Removal and Installation (Service and Repair) .
9. Lower the vehicle.
10. Remove cap or tape from the evaporator outlet tube (1).
11. Install a new O-rings onto the evaporator outlet tube (1). Refer to O-Ring Replacement (O-Ring Replacement) .
12. Connect the evaporator outlet tube (1) to the A/C compressor hose assembly (2).
13. Install the A/C tube connector to the evaporator outlet tube and A/C compressor hose assembly. Refer to Air Conditioning Line/Tube Connector Removal/Replacement (Air Conditioning Line/Tube Connector Removal/Replacement) .
14. Remove cap or tape from the A/C condenser fitting.
15. Install a new sealing washer onto the compressor hose assembly. Refer to Sealing Washer Replacement (Sealing Washer Replacement) .
16. Connect the A/C compressor hose assembly to the A/C condenser fitting.
17. Install the A/C compressor hose assembly bolt (1) to the A/C condenser fitting.
Tighten the bolt to 16 N.m (12 lb ft).
18. Install the radiator support. Refer to Radiator Support Replacement (Service and Repair) .
19. Recharge the A/C system. Refer to Refrigerant Recovery and Recharging (Refrigerant Recovery and Recharging) .
20. Leak test the fittings of the component using J 39400-A .