Operation CHARM: Car repair manuals for everyone.

B0968




DTC B0968

Diagnostic Instructions

* Perform the Diagnostic System Check - Vehicle (Initial Inspection and Diagnostic Overview) prior to using this diagnostic procedure.
* Review Strategy Based Diagnosis (Initial Inspection and Diagnostic Overview) for an overview of the diagnostic approach.
* Diagnostic Procedure Instructions (Initial Inspection and Diagnostic Overview) provides an overview of each diagnostic category.

DTC Descriptor
DTC B0968 00
- Parking Aid Indicator Circuit

Diagnostic Fault Information





Circuit/System Description

The object alarm module directly controls the parking assist indicators located in the information center telltale assembly. The information center telltale assembly consists of two amber and one red LED that indicate the distance of an object from the rear bumper. As objects become progressively closer to the bumper, the object alarm module will illuminate the LEDs in a sequence: one amber LED, both amber LEDs, and lastly, both amber LEDs and the red LED. The LEDs are supplied voltage by the object alarm module. Each LED is also discretely controlled by the object alarm module.

Conditions for Running the DTC

* DTC B1325 is not set
* Ignition voltage is between 9-16 volts

Conditions for Setting the DTC

The object alarm module detects that one of the three indicator control circuits or the supply voltage is shorted to ground.

Action Taken When the DTC Sets

* Parking assist is disabled.
* The object alarm module commands the red indicator ON.
* The object alarm module sends a serial data message to the instrument panel cluster (IPC) to display SERVICE PARK ASSIST message in the driver information center (DIC) and a chime will sound.

Conditions for Clearing

* The DTC will transition to history when the fault is no longer present.
* A history DTC will clear after 100 malfunction-free ignition cycles.

Reference Information
Schematic Reference

Object Detection Schematics ([1][2]Collision Avoidance and Parking Assist Systems)
Connector End View Reference

Component Connector End Views (Connector Views)
Description and Operation

Object Detection Description and Operation (PIDS) (Object Detection Description and Operation (PIDS))Object Detection Description and Operation (Rear Parking Assist) (Object Detection Description and Operation (Rear Parking Assist))
Electrical Information Reference

* Circuit Testing (Component Tests and General Diagnostics)
* Connector Repairs (Component Tests and General Diagnostics)
* Testing for Intermittent Conditions and Poor Connections (Component Tests and General Diagnostics)
* Wiring Repairs (Component Tests and General Diagnostics)

Scan Tool Reference

Control Module References (Programming and Relearning) for scan tool information

Circuit/System Verification

Ignition ON, command the Rear Red LED, Rear Yellow LED 1, and Rear Yellow LED 2 ON and OFF with a scan tool. The appropriate indicator should turn on and off as commanded.

Circuit/System Testing

1. Ignition OFF, disconnect the harness connector at the information center telltale assembly.
2. Ignition ON, test for B+ between the supply voltage circuit terminal A and ground.

If less than the specified range, test the supply voltage circuit terminal for a short to ground or an open/high resistance. If the circuit tests normal, replace the object alarm module.
If greater than the specified range, test the control circuit terminal for a short to voltage. If the circuit tests normal, replace the object alarm module.

3. Command the appropriate LED ON with a scan tool and test for B+ between the appropriate control circuit listed below and ground:

* Amber 1 LED - terminal B
* Amber 2 LED - terminal C
* Red LED - terminal D

If less than the specified range, test the control circuit terminal for a short to ground or an open/high resistance. If the circuit tests normal, replace the object alarm module.
If greater than the specified range, test the control circuit terminal for a short to voltage. If the circuit tests normal, replace the object alarm module.

4. If all circuits test normal, test or replace the information center telltale assembly.

Repair Instructions

Perform the Diagnostic Repair Verification (Verification Tests) after completing the diagnostic procedure.

* Information Center Telltale Assembly Replacement (Service and Repair)
* Control Module References (Programming and Relearning) for object alarm module replacement, setup, and programming