Operation CHARM: Car repair manuals for everyone.
Home >> Cadillac >> 2010 >> CTS Sedan RWD V6-3.0L >> Repair and Diagnosis >> Transmission and Drivetrain >> Automatic Transmission/Transaxle >> Service and Repair >> Removal and Replacement >> Transmission Replacement

Transmission Replacement




Transmission Replacement (Rear Wheel Drive)

Note: NEW cooler pipe O-rings and torque converter bolts will be required each time the transmission is removed and installed.

Removal Procedure

1. If equipped with 3.6L engine, Remove the thermostat housing. Refer to Engine Coolant Thermostat Housing Replacement.
2. Remove the exhaust system. Refer to Exhaust System Replacement (LSA) (Exhaust System Replacement)Exhaust System Replacement (LF1) (Exhaust System Replacement)Exhaust System Replacement (Single) (Exhaust System Replacement (Single))Exhaust System Replacement (LLT) (Exhaust System Replacement).
3. Remove the catalytic converters. Refer to Catalytic Converter Replacement - Left Side (LLT) (Catalytic Converter Replacement - Left Side)Catalytic Converter Replacement - Left Side (LSA) (Catalytic Converter Replacement - Left Side)Catalytic Converter Replacement - Left Side (LF1) (Catalytic Converter Replacement - Left Side) and Catalytic Converter Replacement - Right Side (LLT) (Catalytic Converter Replacement - Right Side)Catalytic Converter Replacement - Right Side (LSA) (Catalytic Converter Replacement - Right Side)Catalytic Converter Replacement - Right Side (LF1) (Catalytic Converter Replacement - Right Side).
4. Remove the propeller shaft. Refer to Rear Propeller Shaft Replacement (RPO LSA) (Service and Repair)Rear Propeller Shaft Replacement (RPO LLT/LF1with MX7 or MN6) (Service and Repair)Rear Propeller Shaft Replacement (RPO LLT, LF1 with MXO) (Service and Repair).




5. Disconnect the shift linkage from the transmission.




6. Remove the transmission vent hose from the retaining clips (6) on the transmission support.




7. Disconnect the transmission wiring harness connector (4) from the transmission by releasing the locking mechanism and rotating the latch counterclockwise.
8. Remove the wiring harness retainers (1) from the transmission.
9. Remove the oxygen sensor wiring harness connector (2) from the transmission.
10. Place an oil drain pan under the transmission fluid cooler pipes.




11. Remove the transmission fluid cooler pipes (1) from the transmission, and position aside. Refer to Transmission Fluid Cooler Hose/Pipe Replacement (With VO3) (Transmission Fluid Cooler Hose/Pipe Replacement (With VO3))Transmission Fluid Cooler Hose/Pipe Replacement (Without VO3) (Transmission Fluid Cooler Hose/Pipe Replacement (Without VO3)).
12. Remove and discard the O-rings. Do NOT reuse the O-rings.
13. Plug the open outlet ports to prevent fluid loss and contamination.




14. Remove the transmission close out plug (1).
15. Mark the torque converter to flexplate/flywheel orientation to ensure proper realignment.
16. Remove the starter motor. Refer to Starter Replacement (LF1/LLT) (Service and Repair)Starter Replacement (LSA) (Service and Repair).




17. Repeat the following steps for all torque converter bolts (1):

1. Rotate the harmonic balancer center bolt clockwise ONLY, in order to align the torque converter bolt with the access hole.
2. Remove and discard the torque converter bolt.

18. Support the transmission with a suitable transmission jack.
19. Remove the transmission support. Refer to Transmission Support Replacement (Manual except CTS-V) (Service and Repair)Transmission Support Replacement (Automatic RWD except CTS-V) (Service and Repair)Transmission Support Replacement (Automatic CTS-V) (Service and Repair)Transmission Support Replacement (Manual CTS-V) (Service and Repair)Transmission Support Replacement (Automatic AWD) (Service and Repair).
20. Lower the transmission.




21. Disconnect the transmission vent hose (4) from the transmission vent pipe (1).




22. Remove the wiring harness retainers (2) from the transmission.
23. Position the transmission wiring harness (1) and vent tube out of the way.




24. Remove the transmission mounting bolts (1-6).
25. Pull the transmission free from the engine dowels.

Note: Ensure clearance is maintained between the transmission and the following:

* The wiring harness
* The vent tube
* The cooler pipes

26. Carefully lower the transmission from the vehicle.
27. Flush the transmission oil cooler if necessary. Refer to Transmission Fluid Cooler Flushing and Flow Test (Testing and Inspection).

Installation Procedure

Note: Ensure clearance is maintained between the transmission and the following:

* The wiring harness
* The vent tube
* The cooler pipes

1. Using the transmission jack, carefully raise the transmission to the engine.




2. Align the transmission with the engine dowels.

Caution: Refer to Fastener Caution (Fastener Caution).

3. Install the transmission mounting bolts and tighten to 50 Nm (37 lb ft).




4. Position the engine wiring harness (1) to the original location.
5. Install the wiring harness retainers (2) to the transmission.




6. Connect the transmission vent hose (4) to the transmission vent pipe (1).
7. Raise the transmission to the installed position.
8. Install the transmission support. Refer to Transmission Support Replacement (Manual except CTS-V) (Service and Repair)Transmission Support Replacement (Automatic RWD except CTS-V) (Service and Repair)Transmission Support Replacement (Automatic CTS-V) (Service and Repair)Transmission Support Replacement (Manual CTS-V) (Service and Repair)Transmission Support Replacement (Automatic AWD) (Service and Repair).
9. Remove the jack from under the transmission.
10. Align the torque converter to flexplate/flywheel orientation marks made during the removal procedure.





Note: Torque converter bolts are self locking and must be replaced with NEW torque converter bolts every time the bolts are removed.

11. Complete the following steps for all torque converter bolts (1):

1. Rotate the harmonic balancer center bolt clockwise ONLY, in order to align the torque converter bolt holes in the flexplate/flywheel with the access hole in the engine block.
2. To aid in alignment of the torque converter to the flexplate/flywheel. Install all NEW torque converter bolts before fully tightening to 63 Nm (46 lb ft).

12. Remove the starter motor. Refer to Starter Replacement (LF1/LLT) (Service and Repair)Starter Replacement (LSA) (Service and Repair).




13. Install the transmission close out plug (1).




14. Place NEW O-rings over the transmission fluid cooler pipes.
15. Install the transmission fluid cooler pipes (1) to the transmission. Refer to Transmission Fluid Cooler Hose/Pipe Replacement (With VO3) (Transmission Fluid Cooler Hose/Pipe Replacement (With VO3))Transmission Fluid Cooler Hose/Pipe Replacement (Without VO3) (Transmission Fluid Cooler Hose/Pipe Replacement (Without VO3)).




16. Install the oxygen sensor wiring harness connector (2) from the transmission.
17. Install the wiring harness retainers (1) to the transmission.
18. Connect the transmission wiring harness connector (5) to the transmission by rotating the locking latch clockwise.




19. Install the transmission vent hose to the retaining clips (6) on the transmission support.




20. Install the shift linkage to the transmission.
21. Install the transmission manual shift shaft nut and tighten to 15 Nm (11 lb ft).
22. Install the propeller shaft. Refer to Rear Propeller Shaft Replacement (RPO LSA) (Service and Repair)Rear Propeller Shaft Replacement (RPO LLT/LF1with MX7 or MN6) (Service and Repair)Rear Propeller Shaft Replacement (RPO LLT, LF1 with MXO) (Service and Repair).
23. Install the catalytic converters. Refer to Catalytic Converter Replacement - Left Side (LLT) (Catalytic Converter Replacement - Left Side)Catalytic Converter Replacement - Left Side (LSA) (Catalytic Converter Replacement - Left Side)Catalytic Converter Replacement - Left Side (LF1) (Catalytic Converter Replacement - Left Side) and Catalytic Converter Replacement - Right Side (LLT) (Catalytic Converter Replacement - Right Side)Catalytic Converter Replacement - Right Side (LSA) (Catalytic Converter Replacement - Right Side)Catalytic Converter Replacement - Right Side (LF1) (Catalytic Converter Replacement - Right Side).
24. Install the exhaust system. Refer to Exhaust System Replacement (LSA) (Exhaust System Replacement)Exhaust System Replacement (LF1) (Exhaust System Replacement)Exhaust System Replacement (Single) (Exhaust System Replacement (Single))Exhaust System Replacement (LLT) (Exhaust System Replacement).
25. Lower the vehicle.
26. Install the thermostat housing. Refer to Engine Coolant Thermostat Housing Replacement.
27. Check the transmission fluid level and fill if necessary. Refer to Transmission Fluid Level and Condition Check (Transmission Fluid Level and Condition Check).
28. Adjust the shift control linkage. Refer to Shift Control Linkage Adjustment (All Wheel Drive) (Adjustments)Shift Control Linkage Adjustment (Rear Wheel Drive) (Adjustments).

Transmission Final Test and Inspection

Complete the following procedure after the transmission is installed in the vehicle:

1. With the ignition OFF or disconnected, crank the engine several times. Listen for any unusual noises or evidence that any parts are binding.
2. Start the engine and listen for abnormal conditions.
3. While the engine continues to idle, raise and support the vehicle. Refer to Lifting and Jacking the Vehicle (Service and Repair).
4. Inspect for fluid leaks while the engine is idling.
5. Perform a final inspection for the proper fluid level.
6. Lower the vehicle.
7. Calibrate the transmission control module (TCM). Refer to Control Module References (Programming and Relearning).

Note: It is recommended that transmission adaptive pressure (TAP) information be reset.

Resetting the TAP values using a scan tool will erase all learned values in all cells. As a result, The ECM, PCM or TCM will need to relearn TAP values. Transmission performance may be affected as new TAP values are learned.

8. Reset the TAP values. Refer to Transmission Adaptive Functions (Transmission Adaptive Functions).
9. Road test the vehicle.

pro multis · About Operation CHARM