Moisture Sensing Feature Inoperative
Moisture Sensing Feature Inoperative
Diagnostic Instructions
* Perform the Diagnostic System Check - Vehicle (Diagnostic System Check - Vehicle) prior to using this diagnostic procedure.
* Review Strategy Based Diagnosis (Strategy Based Diagnosis) for an overview of the diagnostic approach.
* Diagnostic Procedure Instructions (Diagnostic Procedure Instructions) provides an overview of each diagnostic category.
Diagnostic Fault Information
Circuit/System Description
Accessory voltage is supplied to the outside moisture sensor through the 10A RAP fuse located in the rear fuse block. The sensor is grounded through the ground circuit and G402. Whenever the ignition is in the run or accessory positions, the BCM sends the wiper/washer switch status using a pulse width modulation (PWM) signal through the outside moisture sensor signal 1 circuit to the outside moisture sensor. When a wipe cycle is needed, the moisture sensor sends a PWM voltage signal through the moisture sensor signal 2 circuit back to the BCM requesting the wiper operation.
The outside moisture sensor uses the moisture sensor signal 2 circuit to command wiper motor wipe cycles and to confirm the moisture sensor signal 1 is being received. If at anytime communication between the outside moisture sensor and BCM is lost, the BCM will use the inputs from the windshield wiper/washer switch in the delay positions to operate the wiper motor at continuous variable delay intervals.
Reference Information
Schematic Reference
Wiper/Washer Schematics (Electrical Diagrams)
Connector End View Reference
Component Connector End Views (Connector Views)
Description and Operation
Wiper/Washer System Description and Operation (STS) (Wiper/Washer System (STS))Wiper/Washer System Description and Operation (STS-V) (Wiper/Washer System (STS-V))
Electrical Information Reference
* Circuit Testing (Circuit Testing)
* Connector Repairs (Connector Repairs)
* Testing for Intermittent Conditions and Poor Connections (Testing for Intermittent Conditions and Poor Connections)
* Wiring Repairs (Wiring Repairs)
Scan Tool Reference
Control Module References (Programming and Relearning) for scan tool information
Circuit/System Verification
Ignition ON, wiper switch in the LO position. The windshield wipers should operate at low speed. If the windshield wipers do not operate, refer to Windshield Wiper System Malfunction (Windshield Wiper System Malfunction).
Circuit/System Testing
1. Ignition OFF, disconnect the harness connector at the outside moisture sensor.
2. Test for less than 5.0 ohm between the ground circuit terminal 3 and ground.
• If greater than the specified range, test the ground circuit for an open/high resistance.
3. Ignition ON, verify that a test lamp illuminates between accessory voltage circuit terminal 4 and ground.
• If the test does not illuminate, test the accessory voltage circuit for a short to ground or an open/high resistance.
4. Ignition ON, test for 4.0-8.5 V between signal circuit terminal 2 and ground.
• If greater than the specified range, test the signal circuit for a short to voltage. If the circuit tests normal, replace the outside moisture sensor.
• If less than the specified range, test the signal circuit for a short to ground or an open/high resistance. If the circuit tests normal, replace the outside moisture sensor.
5. Ignition OFF, reconnect the harness connector to the rain sensor.
6. Disconnect the (X4) harness connector at the BCM.
7. Ignition ON, test for 5-10 V between the signal circuit terminal 14 and ground.
• If greater than the specified range, test the signal circuit for a short to voltage. If the circuit tests normal, replace the outside moisture sensor.
• If less than the specified range, test the signal circuit for a short to ground or an open/high resistance. If the circuit tests normal, replace the outside moisture sensor.
8. If all circuits test normal, replace the BCM.
Repair Instructions
Perform the Diagnostic Repair Verification (Verification Tests) after completing the diagnostic procedure.
* Windshield Outside Moisture Sensor Replacement (Service and Repair)
* Control Module References (Programming and Relearning) for IPC replacement, setup, and programming