Engine Support Fixture

Engine Support Fixture

Special Tools
* J 28467-B Universal Engine Support Fixture
* J 28467-501 Engine Support Fixture Adapters

Installation Procedure




1. Remove the air inlet grille. Refer to Air Inlet Grille Panel Replacement (Service and Repair).
2. Install the J 28467-3 strut tower tube (2) into the J 28467-501 (1).




3. Remove the surge tank nuts and push pin retainer.
4. Remove the surge tank from the studs and position the tank aside.




5. Remove the engine mount strut brace bolt and nut.
6. Remove the engine mount strut brace.




7. Remove the engine mount strut bolt.
8. Remove the engine mount strut.
9. Remove the front compartment sight shield. Refer to Front Compartment Sight Shields Replacement (Front Compartment Sight Shields Replacement).




10. Install the J 28467-2A radiator shelf tube on top of the J 28467-3 strut tower tube.




11. Install the round tube of the J 28467-4A front support assembly through the large hole in the J 28467-2A radiator shelf tube. The hole used in the J 28467-2A radiator shelf tube depends on the vehicle application.
12. Place the rubber padded foot of the J 28467-4A front support assembly on the upper tie bar.
13. Install the J 28467-9 7/16 in x 2.0 in quick release pin through the hole in the J 28467-4A front support assembly in order to level the J 28467-2A radiator shelf tube.




14. Install the J 28467-1A cross bracket assembly.
15. Hand tighten the J 28467-1A cross bracket assembly wing nuts.




16. Install the J 28467-7A lift hook through the J 28467-6A lift hook bracket.
17. Install the 1/2 in lift hook washer and J 28467-34 lift hook wing nut onto the J 28467-7A lift hook.




18. Install the J 28467-6A assembled lift hook bracket (1) over the J 28467-3 strut tower tube (2).
19. Adjust the J 28467-6A assembled lift hook bracket (1) in order to align the hook with the rear engine lift hook bracket.




20. Install the J 28467-7A lift hook through the rear engine lift hook bracket. Ensure the hook does not damage the surrounding components.
21. Repeat steps 18 and 19.




22. Install the J 28467-6A assembled lift hook bracket (1) over the J 28467-2A radiator shelf tube (2).
23. Adjust the J 28467-6A assembled lift hook bracket (1) in order to align the hook with the torque strut bracket.




24. Install the J 28467-7A lift hook through the engine mount strut bracket. Ensure the hook does not damage the surrounding components.
25. Hand tighten the J 28467-34 lift hook wing nuts securely to remove all slack from the engine support fixture assembly.

Removal Procedure




1. Remove the J 28467-7A lift hook from the engine mount strut bracket.
2. Remove the J 28467-B .
3. Remove the J 28467-501 .




4. Install the engine mount strut.

Caution: Refer to Fastener Caution (Fastener Caution).

5. Install the engine mount strut bolt.

Tighten the bolt to 70 Nm (52 lb ft).




6. Install the engine mount strut brace.
7. Install the engine mount strut brace bolt and nut.

* Tighten the bolt to 50 Nm (37 lb ft).
* Tighten the nut to 70 Nm (52 lb ft).




8. Position the surge tank to the studs.
9. Install the surge tank nuts and push pin retainer.

Tighten the nuts to 6 Nm (53 lb in).

10. Install the front compartment sight shield. Refer to Front Compartment Sight Shields Replacement (Front Compartment Sight Shields Replacement).
11. Install the air inlet grille. Refer to Air Inlet Grille Panel Replacement (Service and Repair).