B370C
DTC B370C or B370D
Diagnostic Instructions
* Perform the Diagnostic System Check - Vehicle Diagnostic System Check - Vehicle prior to using this diagnostic procedure.
* Review Strategy Based Diagnosis Strategy Based Diagnosis for an overview of the diagnostic approach.
* Diagnostic Procedure Instructions Diagnostic Procedure Instructions provides an overview of each diagnostic category.
DTC Descriptor
DTC B370C 00
- Rain Sensor Intensity Signal Circuit.
DTC B370D 00
- Rain Sensor Mode Control Circuit.
Diagnostic Fault Information
Circuit/System Description
Ignition voltage is supplied to the windshield outside moisture sensor from the body control module (BCM). Whenever the ignition is in the run or accessory positions, the BCM sends the wiper/washer switch status using a pulse width modulated (PWM) signal through the windshield outside moisture sensor control circuit to the outside moisture sensor. When a wipe cycle is needed, the moisture sensor sends a PWM voltage signal through the moisture sensor signal circuit back to the BCM requesting the wiper operation.
The windshield outside moisture sensor uses the moisture sensor control circuit to command wiper motor wipe cycles and to confirm the moisture sensor signal circuit is being received. If at anytime communication between the windshield outside moisture sensor and BCM is lost, the BCM will use the inputs from the windshield wiper/washer switch in the delay positions to operate the wiper motor at continuous variable delay intervals.
Conditions for Running the DTC
Ignition in Run or Accessory positions.
Conditions for Setting the DTC
B370C
An open, short to ground or a short to voltage has been detected on the signal circuit.
B370D
An open, short to ground or a short to voltage has been detected on the control circuit.
Action Taken When the DTC Sets
Moisture sensitive wiper operation is suspended so long as the fault is present. The wipers will still operate normally in all other modes.
Conditions for Clearing the DTC
* A current DTC will clear when the fault is no longer present.
* A history DTC will clear after 40 malfunction-free ignition cycles.
Reference Information
Schematic Reference
Wiper/Washer Schematics Electrical Diagrams
Connector End View Reference
Component Connector End Views Connector Views
Description and Operation
Wiper/Washer System Description and Operation (Wiper and Washers) Wiper/Washer System (Wipers and Washers)
Electrical Information Reference
* Circuit Testing Circuit Testing
* Connector Repairs Connector Repairs
* Testing for Intermittent Conditions and Poor Connections Testing for Intermittent Conditions and Poor Connections
* Wiring Repairs Wiring Repairs
Scan Tool Reference
Control Module References Control Module References for scan tool information
Circuit/System Verification
Ignition ON, wiper switch in the LOW position. The windshield wipers should operate at low speed. If the windshield wipers do not operate, refer to Windshield Wiper System Malfunction Windshield Wiper System Malfunction.
Circuit/System Testing
1. Ignition OFF, disconnect the harness connector at the windshield outside moisture sensor.
2. Test for less than 5.0 ohms between the ground circuit terminal 3 and ground.
• If greater than the specified range, test the ground circuit for an open/high resistance.
3. Ignition ON, verify that a test lamp illuminates between ignition voltage circuit terminal 4 and ground.
• If the test lamp does not illuminate, test the ignition voltage circuit for a short to ground or an open/high resistance.
4. Ignition ON, test for 4.0 - 8.5 volts between the control circuit terminal 1 and ground.
• If less than the specified range, test the control circuit for a short to ground or an open/high resistance. If the circuit tests normal, replace the BCM.
• If greater than the specified range, test the control circuit for a short to voltage. If the circuit tests normal, replace the BCM.
5. Ignition OFF, connect the harness connector at the windshield outside moisture sensor.
6. Disconnect the X4 harness connector at the BCM.
7. Ignition ON, test for 8.0 - 10.0 volts between the signal circuit terminal 18 and ground.
• If less than the specified range, test the signal circuit for a short to ground or an open/high resistance. If the circuit tests normal, replace the windshield outside moisture sensor.
• If greater than the specified range, test the signal circuit for a short to voltage. If the circuit tests normal, replace the windshield outside moisture sensor.
8. If all circuits test normal, replace the BCM.
Repair Instructions
* Perform the Diagnostic Repair Verification Verification Tests after completing the diagnostic procedure.
* Control Module References Control Module References for BCM replacement, setup, and programming
* Windshield Outside Moisture Sensor Replacement Service and Repair