B0283
DTC B0283
Diagnostic Instructions
* Perform the Diagnostic System Check - Vehicle Diagnostic System Check - Vehicle prior to using this diagnostic procedure.
* Review Strategy Based Diagnosis Strategy Based Diagnosis for an overview of the diagnostic approach.
* Diagnostic Procedure Instructions Diagnostic Procedure Instructions provides an overview of each diagnostic category.
DTC Descriptors
DTC B0283 02
- Rear Defrost Circuit Short To Ground
DTC B0283 05
- Rear Defrost Circuit Short To Battery or Open
Diagnostic Fault Information
Circuit/System Description
When the HVAC Control Module receives a rear window defog request from the HVAC face plate, the HVAC Control Module control the coil side of the Rear Defogger Relay. This will energize the relay causing the contacts within the relay to close and provide B+ voltage to the rear window defogger grid.
Conditions for Running the DTC
When the relay is being actively commanded by the HVAC Control Module
Conditions for Setting the DTC
B0283 02
The HVAC Control Module detects a short to ground in the relay coil control circuit.
B0283 05
The HVAC Control Module detects a short to voltage or an open/high resistance in the relay coil control circuit or an open/high resistance in the relay coil ground circuit
Action Taken When the DTC Sets
B0283 02
The rear window defogger will be inoperative.
B0283 05
The rear window defogger will be inoperative or continuously active depending upon the fault.
Conditions for Clearing the DTC
* The DTC will be current for as long as the fault is present.
* When the fault is no longer present, the DTC will be a history DTC.
* A history DTC will clear after 50 ignition cycles.
Reference Information
Schematic Reference
Defogger Schematics Electrical Diagrams
Connector End View Reference
Component Connector End Views Fuel Pump and Level Sensor Assembly
Description and Operation
Rear Window Defogger Description and Operation Description and Operation
Electrical Information Reference
* Circuit Testing Circuit Testing
* Connector Repairs Connector Repairs
* Testing for Intermittent Conditions and Poor Connections Testing for Intermittent Conditions and Poor Connections
* Wiring Repairs Wiring Repairs
Scan Tool Reference
Control Module References Control Module References for scan tool information
Circuit/System Verification
1. Engine Running.
2. Verify the E18 Rear Defogger Grid turns ON and OFF when commanding the Rear Defogger On and Off with a scan tool.
• If the E18 Rear Defogger Grid does not turn ON or OFF
Refer to Circuit/System Testing
• If the E18 Rear Defogger Grid turns ON and OFF
3. All OK.
Circuit/System Testing
1. Ignition OFF and all vehicle systems OFF, disconnect the KR5 Rear Defogger Relay. It may take up to 2 minutes for all vehicle systems to power down.
2. Test for less than 10 ohms between the ground circuit terminal 85 and ground.
• If 10 ohms or greater
1. Ignition OFF.
2. Test for less than 2 ohms in the ground circuit end to end.
• If 2 ohms or greater, repair the open/high resistance in the circuit.
• If less than 2 ohms, repair the open/high resistance in the ground connection.
• If less than 10 ohms
3. Connect a test lamp between the control circuit terminal 86 and the ground circuit terminal 85, Engine Running.
4. Verify the test lamp turns ON and OFF when commanding the Rear Defogger On and Off with a scan tool.
• If the test lamp is always OFF
1. Ignition OFF, disconnect the harness connector at the K33 HVAC Control Module.
2. Test for infinite resistance between the control circuit and ground.
• If less than infinite resistance, repair the short to ground on the circuit.
• If infinite resistance
3. Test for less than 2 ohms in the control circuit end to end.
• If 2 ohms or greater, repair the open/high resistance in the circuit.
• If less than 2 ohms, replace the K33 HVAC Control Module.
• If the test lamp is always ON
1. Ignition OFF, disconnect the harness connector at the K33 HVAC Control Module, Engine Running.
2. Test for less than 1 V between the control circuit and ground.
• If 1 V or greater, repair the short to voltage on the circuit.
• If less than 1 V, replace the K33 HVAC Control Module.
• If the test lamp turns ON and OFF
5. Test or replace the KR5 Rear Defogger Relay.
Component Testing
Relay Test
1. Ignition OFF, disconnect the KR5 Rear Defogger Relay.
2. Test for 60-180 ohms between terminals 86 and 85.
• If less than 60 ohms or greater than 180 ohms
Replace the KR5 Rear Defogger Relay.
• If between 60-180 ohms
3. Test for infinite resistance between the terminals listed below:
* 86 and 30
* 86 and 87
* 85 and 30
* 85 and 87
• If less than infinite resistance
Replace the KR5 Rear Defogger Relay.
• If infinite resistance
4. Install a 3 A fused jumper wire between relay terminal 86 and 12 V. Install a jumper wire between relay terminal 85 and ground.
5. Test for less than 2 ohms between terminals 30 and 87.
• If 2 ohms or greater
Replace the KR5 Rear Defogger Relay.
• If less than 2 ohms
6. All OK
Repair Instructions
Perform the Diagnostic Repair Verification Verification Tests after completing the repair.
* Relay Replacement (Attached to Wire Harness) Relay Replacement (Attached to Wire Harness)Relay Replacement (Within an Electrical Center) Relay Replacement (Within an Electrical Center)
* Control Module References Control Module References for HVAC Control Module replacement, programming and setup