B3600
DTC B3600
Diagnostic Instructions
* Perform the Diagnostic System Check - Vehicle Diagnostic System Check - Vehicle prior to using this diagnostic procedure.
* Review Strategy Based Diagnosis Strategy Based Diagnosis for an overview of the diagnostic approach.
* Diagnostic Procedure Instructions Diagnostic Procedure Instructions provides an overview of each diagnostic category.
DTC Descriptors
DTC B3600 03
- Passenger Compartment Dimming Request Signal Circuit Low Voltage
DTC B3600 07
- Passenger Compartment Dimming Request Signal Circuit High Voltage
Diagnostic Fault Information
Circuit/System Description
The instrument panel (I/P) dimmer switch is used to increase and decrease the brightness of the interior backlighting components. The I/P dimmer switch provides a voltage signal to the body control module (BCM) that will increase as the brightness of the lights are increased and decrease as the brightness of the lights are decreased. The BCM provides a low reference signal and a B+ voltage reference to the I/P dimmer switch. When the I/P dimmer switch is placed in the desired position, the dimmed voltage setting is applied from the I/P dimmer switch through the I/P dimmer switch signal circuit to the BCM. The BCM interprets the signal and applies a pulse width modulated (PWM) voltage through the light emitting diode (LED) dimming 1 and dimming 2 control circuits illuminating the interior backlighting to the requested level of brightness.
Conditions for Running the DTC
* Battery voltage must be between 9-16 V.
* Park Lamps ON.
Conditions for Setting the DTC
DTC B3600 03
The BCM detects a short to ground or an open/high resistance in the I/P dimmer switch signal circuit.
DTC B3600 07
The BCM detects a short to voltage in the I/P dimmer switch signal circuit.
Actions Taken When the DTC Sets
The BCM will not dim any interior backlighting. All interior backlighting will default to the level selected prior to the fault being present.
Conditions for Clearing the DTC
* The condition responsible for setting the DTC no longer exists.
* A history DTC will clear once 100 consecutive malfunction-free ignition cycles have occurred.
Reference Information
Schematic Reference
Interior Lights Dimming Schematics Interior Lights Dimming Schematics
Connector End View Reference
Component Connector End Views Fuel Pump and Level Sensor Assembly
Description and Operation
Interior Lighting Systems Description and Operation Interior Lighting Systems
Electrical Information Reference
* Circuit Testing Circuit Testing
* Connector Repairs Connector Repairs
* Testing for Intermittent Conditions and Poor Connections Testing for Intermittent Conditions and Poor Connections
* Wiring Repairs Wiring Repairs
Scan Tool Reference
Control Module References Control Module References for scan tool information
Circuit/System Testing
1. Ignition OFF, disconnect the harness connector at the S36 instrument panel dimmer switch, ignition ON.
2. Test for B+ between the B+ reference circuit terminal 6 and ground.
• If less than B+
1. Ignition OFF, disconnect the X1 harness connector at the K9 body control module.
2. Test for infinite resistance between the B+ reference circuit and ground.
• If less than infinite resistance, repair the short to ground on the circuit.
• If infinite resistance
3. Test for less than 2 ohms in the B+ reference circuit end to end.
• If 2 ohms or greater, repair the open/high resistance in the circuit.
• If less than 2 ohms, replace the K9 body control module.
• If B+
3. Verify the scan tool LED Backlight Dimming Command parameter is greater than 40%.
• If 40% or less
1. Ignition OFF, disconnect the X2 harness connector at the K9 body control module, ignition ON.
2. Test for less than 1 V between the signal circuit terminal 2 and ground.
• If 1 V or greater, repair the short to voltage on the circuit.
• If less than 1 V, replace the K9 body control module.
• If greater than 40%
4. Install a 3 A fused jumper wire between the signal circuit terminal 2 and the B+ reference circuit terminal 6.
5. Verify the scan tool LED Backlight Dimming Command parameter is less than 30%.
• If 30% or greater
1. Ignition OFF, disconnect the X2 harness connector at the K9 body control module.
2. Test for infinite resistance between the signal circuit and ground.
• If less than infinite resistance, repair the short to ground on the circuit.
• If infinite resistance
3. Test for less than 2 ohms in the signal circuit end to end.
• If 2 ohms or greater, repair the open/high resistance in the circuit.
• If less than 2 ohms, replace the K9 body control module.
• If less than 30%
6. Test or replace the S36 instrument panel dimmer switch.
Repair Instructions
Perform the Diagnostic Repair Verification Verification Tests after completing the repair.
* Interior Lamp Switch Replacement (Override) Interior Lamp Switch Replacement (Override)Interior Lamp Switch Replacement (Reading) Interior Lamp Switch Replacement (Reading)
* Control Module References Control Module References for BCM replacement, programming, and setup