Radio/Audio System
Radio/Audio System Description and Operation
The entertainment system on this vehicle may have several different configurations available to it. To determine the specific configuration of the vehicle, please see the Service Parts ID Label, and refer to RPO Code List RPO Code List.
Each item in the list below represents topics covered in detail below.
* Data Communications
* Remote Radio Receiver
* Human Machine Interface Module
* Remote Optical Drive
* Audio Amplifier (If equipped)
* Speaker Operation
* Information Display
* Infotainment Controls
* Antenna System
* Radio Reception
* Theft Deterrent
* Bluetooth (R) (if equipped)
* Applications (if equipped)
* Auxiliary Audio Input Jack
* USB Port and SD Card Reader
* Navigation System Components and Features (if equipped)
* OnStar (R)
* Steering Wheel Controls (If equipped)
* Auto Volume Control
Data Communications
The infotainment system communicates with other devices on multiple serial data networks during operation.
Media Oriented Systems Transport (MOST)
At the core of the infotainment system is the Media Oriented Systems Transport (MOST) bus, a high-speed multimedia network technology. The serial MOST bus uses a ring topology and synchronous data communication to transmit audio, video, data and control information between any devices attached. The MOST bus uses a dual wire structure to communicate among these devices.
A MOST communication enable circuit is also connected to all components on the MOST bus. The MOST enable circuit is used to wake the network and trigger network diagnostics. Any component on the MOST bus may assert the enable circuit, but communications are initiated by the MOST bus master.
The MOST bus master is the device responsible for normal wake up and initialization of communication on the network. The MOST bus master receives vehicle power state information from the vehicle power mode master. The MOST bus master uses this information to control the power state of the infotainment system.
The MOST bus master is also responsible for maintaining known good network configuration. The MOST bus master will be the device that reports MOST bus errors/DTCs.
The Remote Radio Receiver, Human Machine Interface Module, Remote Optical Drive, Audio Amplifier and the Instrument Panel Cluster all communicate on the MOST bus.
Local Interconnect Network (LIN)
The Local Interconnect Network (LIN) Bus is a single wire communication system. This bus is used to exchange information between a master control module and other smart devices which provide supporting functionality.
The Remote Radio Receiver, Human Machine Interface Module, Information Display, Infotainment Controls and the Multifunction (tunnel) Controls all communicate on the LIN bus.
GMLAN
The Remote Radio Receiver and the Human Machine Interface Module communicate with other components and systems in the vehicle via GMLAN.
Remote Radio Receiver
The radio is the MOST BUS master. The radio also communicates with other components and systems within the vehicle via GMLAN.
The remote radio receiver is responsible for receiving all broadcast audio bands. Broadcast signals from AM, FM, and XM bands are transmitted to the radio via the vehicle antenna systems.
Radio Power
The radio receives battery power and ground from the vehicle harness.
The radio does not use a discrete ignition feed circuit for power moding. The power mode master provides the system power mode to the radio via serial data messages. The power mode master determines the system power mode by processing power mode information from ignition switch inputs. Serial data power modes supported by the radio are OFF, ACCESSORY, RUN, and CRANK REQUEST.
Radio Audio Outputs
The radio outputs all audio signals digitally over the MOST bus.
Human Machine Interface Module
The human machine interface module is responsible for the following: Video for the infotainment display, Bluetooth (R), USB, memory card reader, and speech recognition functions.
The human machine interface module communicates with the info display module via the LIN bus for control information, touch communications and dimming level. Digital video data is sent to the display through a dedicated video cable.
Remote Optical Drive
The remote CD player receives control information and outputs digital audio over the MOST bus.
Audio Amplifier (If equipped)
Amplifier Interface
A fused battery voltage circuit provides the main amplifier power. The audio amplifier is a participant on the MOST network. The audio amplifier receives audio signals and control information from the MOST bus.
Amplifier Operation
The purpose of the amplifier is to increase the power of a voltage or current signal. The output signal of an amplifier may consist of the same frequencies as the input signal or it may consist of only a portion of the frequencies as in the case of a subwoofer or midrange speaker. The audio amplifier amplifies the signal and sends it to the appropriate speakers.
Each of the audio output channel circuits (+) and (-), at the audio amplifier have a DC bias voltage that is approximately one half of the battery voltage. When using a DMM, each of the audio output channel circuits will measure approximately 6.5V DC. The audio being played on the system is produced by a varying AC voltage that is centered around the DC bias voltage on the same circuit. The AC voltage is what causes the speaker cone to move and produce sound. Both the DC bias voltage and the AC voltage signals are needed for the audio system to properly produce sound.
The audio amplifier is also responsible for operation of active noise cancellation. Refer to Active Noise Cancellation Description and Operation Active Noise Cancellation for more information.
Speaker Operation
Speakers turn electrical energy into mechanical energy to move air, using a permanent magnet and an electromagnet. The electromagnet is energized when the radio or amplifier (if equipped) delivers current to the voice coil on the speaker. The voice coil will form a north and south pole that will cause the voice coil and the speaker cone to move in relation to the permanent magnet. The current delivered to the speaker is rapidly changing alternating current (A/C). This causes the speaker cone to move in two directions producing sound.
Information Display
The information display module has continuous power and ground. Control information, touch communications and dimming level are communicated via the LIN serial data circuit to the human machine interface module.
The human machine interface module sends the info display module digital video data for on-screen display through a dedicated video cable.
The information display provides a feedback on the touch screen and certain controls. Buttons pulse when pressed to affirm that the command is being carried out,
When not actively in use, the screen reverts to minimal images. Proximity Sensing awakens the LCD screen when a hand approaches it.
Infotainment Controls
The infotainment controls have continuous power and ground, and communicate via the LIN serial data circuit with the remote radio receiver. Messages communicated include the following:
* Wake-up/power state messages
* Diagnostic information
* Button presses/knob rotations
* Commands for the state of indicators
* Control back-lighting
HVAC data for controls and status indicators is communicated between the HVAC controls and the HVAC control module with a separate LIN serial data circuit. HVAC status screen information from the HVAC control module is transmitted to the radio on the GMLAN serial data circuit. The radio communicates the desired screen information to the human machine interface module to be sent to the information display using the video data circuits.
Antenna System
Multi-Band Antenna
The multi-band antenna is located on the roof of the vehicle. This type of antenna may be used with the AM/FM radio, but is primarily for cellular and GPS signals, if the vehicle has these features. Keep this antenna clear of snow and ice build up for clear reception. If the vehicle has a sunroof, the performance of the system may be affected if the sunroof is open. Loading items onto the roof of the vehicle can interfere with the performance of the system, ensure the multi-band antenna is not obstructed.
Diversity Antenna
The diversity antenna system uses antennas applied as appliques to the rear glass and two antenna amplifiers. The right antenna 1 receives both AM and FM signals, while the left antenna 2 receives FM signals only. The antenna amplifier receives the signals from the glass antenna. Each antenna amplifier is connected to the radio by a coaxial cable.
The radio antenna amplifier is enabled when the radio is turned on. The radio provides battery voltage to the antenna amplifier using the center conductor of the antenna coaxial cable. When a 12 V signal is seen by the amplifier on the center conductor of the antenna coax, the received signals are amplified.
When the AM band is selected on the radio, the antenna 1 amplifier connects the AM antenna to the radio. When the FM band is selected, both antenna amplifiers provide FM signals to the radio. The radio switches between the two FM antennas, monitoring the signal strength and combines the signals to create one stronger signal.
Radio Reception
AM/FM Radio Signal
The radio signal is sent from a broadcast station and is then received by an antenna. The strength of the signal received depends on the following:
* The power output (wattage) of the broadcasting station
* The location of the vehicle (or receiver) relative to the broadcast tower.
* Height of the broadcast antenna
* Height of the receiving antenna
* Obstacles between the tower and the receiver
* Atmospheric conditions
* What band (AM or FM) the station is broadcasting
* Type of antenna and the ground plane
Digital Radio Receiver (If equipped)
The XM satellite receiver is integrated into the radio. XM satellite radio provides digital radio reception. The XM signal is broadcast from two satellites and, where necessary, terrestrial repeaters. The high power satellites allow the antenna to receive the XM signal even when foliage and other partial obstructions block the antennas view of the satellite. Terrestrial repeaters are used in dense urban areas. These repeaters will receive the satellite signal and re-broadcast them at much higher power levels in order to ensure reception in areas with densely packed tall buildings. A service fee is required in order to receive the XM service.
Radio Data System (RDS)
The RDS feature is available only on FM stations that broadcast RDS information. This system relies upon receiving specific information from these stations and only works when the information is available. While the radio is tuned to an FM-RDS station, the station name or call letters display. RDS data is carried in what is known as a "subcarrier". A subcarrier is a frequency that the FM broadcaster is authorized to use to send data that is not audible in the main audio program.
RDS functions will only work with FM broadcast stations that are broadcasting RDS data. Not all FM Broadcast stations broadcast RDS data or offer all of the RDS services.
The information displayed is dependent upon the information broadcast by the particular station. The information may vary greatly between stations. RDS functions may not work properly when reception is weak, reception is of poor quality, or RDS is not implemented properly by the FM Broadcaster. In some cases, a radio station broadcasting incorrect information may cause the RDS features of the radio to appear to work improperly.
With RDS, the radio can do the following:
* Display text information such as: station identification, type of programming, and general information (artist and song title, station messages, call in phone numbers, etc.).
* Seek to stations broadcasting the selected type of programming
* Receive announcements concerning local and national emergencies
* Receive alert warnings of local or national emergencies. When an alert announcement comes on the current radio station, ALERT! displays. You will hear the announcement, even if the volume is low or a CD is playing. If a CD is playing, play stops during the announcement. Alert announcements cannot be turned off. ALERT! is not affected by tests of the emergency broadcast system. This feature is not supported by all RDS stations.
Theft Deterrent
The radio theft deterrent system is intended to disable or limit radio functionality if incorrect vehicle information is received by the radio. The radio disables functionality if the VIN information received by the radio does not match the VIN information that has been learned by the radio. The radio receives this information via serial data. A possible cause of incorrect VIN info could be the radio was originally installed in another vehicle.
The radio has the following theft operating modes as part of the theft deterrent system:
* Normal Mode: The radio has learned a correct VIN sequence and the VIN information received via serial data matches the learned VIN sequence. In this mode the radio has full functionality.
* No VIN Mode: The radio has not received or learned a correct VIN sequence. In this mode the radio has limited functionality.
* Theft Detected Mode: The radio has learned a correct VIN sequence and the VIN information received via serial data does NOT match the learned VIN sequence. In this mode the radio may be disabled or have limited functionality. The radio display will indicate that theft protection is active.
Bluetooth (R) (If equipped)
Bluetooth (R) wireless technology is a short-range communications technology intended to replace the cables connecting portable and/or fixed devices while maintaining high levels of security. The operating range of the signal is approximately 30 feet.
The available features and functions are determined by the type of device and the software within the devices being used. For a feature or function to operate, it must be supported in both devices.
The first connection between devices is established through a process called pairing. In order to pair two devices, a password (passkey) has to be exchanged between the two devices. One device will generate the password, the other device accepts the password to complete the process. Once the devices are paired, future connections between the devices will occur automatically when the devices are on and within range of each other.
The Bluetooth (R) hardware is internal to the human machine interface module. The human machine interface module supports streaming of data (music, voice, information) from cellular phones and other mobile devices that support those features. The human machine interface module is also capable of interfacing with cellular phones for hands-free features.
* The device must be paired to the system to use the available Bluetooth (R) feature(s). The pairing process must only be performed once for each device, unless that device's information is deleted.
* Up to five devices can be paired, but only one can be connected at any given time.
* Streaming Audio allows playing music from the mobile device wirelessly. Music stored on the mobile device can be viewed and controlled from the display.
* To stream audio from a mobile device, the device must be unlocked, and any additional applications should be closed.
Refer to the vehicle owners manual, supplements, and the device manufacturers information for pairing instructions.
Applications (If equipped)
When the system is equipped with Bluetooth (R), the system is capable of using applications, commonly referred to as apps.
The term application refers to any piece of software that works on a system (hardware) that is being operated by it's own software. Applications are typically small software programs which uses the hardware to perform a specific task, as opposed to operating the entire system.
* For an application to be used, it must be installed on both the vehicle infotainment system and a compatible mobile device.
* The device must be connected to the system. this may be done wirelessly via Bluetooth (R), or via the vehicle USB port. Refer to the device manufacturers information for the proper connection method.
* When the device is connected, the vehicle infotainment system is used to remotely access and control the application on the mobile device.
* The application must work correctly on the device to work with the vehicle infotainment system.
* The user may be required to log-in to the application on the mobile device before using the application from the vehicle controls.
* Using applications will use the device's data plan.
* The device must be unlocked, and any additional applications should be closed.
Refer to the owner's manual and supplements for information on mobile devices, control, and operation.
Auxiliary Audio Input Jack (If equipped)
The infotainment system may have a 3.5mm (1/8 in.) auxiliary audio input jack located in the center console. The auxiliary audio input jack interfaces directly with the radio. When a portable audio playback device is connected to the auxiliary jack, an internal switch detects the connection and the radio will switch to AUX as the audio source. Audio signals from the device are sent to the radio from the auxiliary jack via the left, right, and common audio signal circuits.
* When a device is first connected to the 3.5mm (1/8 in.) input jack the infotainment system automatically switches to that device. If an auxiliary device has already been connected, press the AUX or CD/AUX button to select the device.
* Playback of an audio device that is connected to the 3.5mm jack can only be controlled using the controls on the device.
* The volume control on the device may need to be adjusted to ensure sufficient playback volume through the infotainment system.
USB Port and SD Card Reader
The infotainment system has a USB port and SD card reader slot located in the center console. The USB port and the card reader slot interface with a hub device, internal to the auxiliary jack, USB, and memory card receptacle assembly. The auxiliary jack, USB, and memory card receptacle assembly receives fused battery voltage and ground from the harness to power the internal hub device as well as providing additional amperage to power USB devices.
The internal hub device interfaces directly with the human machine interface module via a standard USB cable. A Mini type USB connector is used to connect the cable at the USB port and at the human machine interface module and at the auxiliary jack, USB, and memory card receptacle. Standard USB male to female connections are typically used for connecting USB cables together where an in-line connection is required. An in-line cable connection is typically found between the console and I/P harness.
USB Port
The USB port allows connectivity to the infotainment system from portable media players or a USB storage device (memory stick/ flash drive). When a device is connected to the USB port, the system detects the device and switches to USB as the audio source. Once connected, the device can be controlled from the radio controls.
Not all portable media player devices or file types are compatible. Connection to USB HUB devices is not supported.
Refer to the owner's manual for information on USB devices, control, and operation.
SD Card Reader
The infotainment system uses the SD card reader as a mass storage device, similar to a USB storage device.
Refer to the owners manual for information on media types supported via the SD card reader.
Navigation System Components and Features (if equipped)
The human machine interface module provides navigation functionality, if equipped. The human machine interface module provides the following:
* Connection to the global positioning system (GPS) antenna, which provides the vehicle position information.
* Map data for navigation and map route guidance, stored in the human machine interface modules internal memory.
* Route guidance with verbal prompts to the operator.
* Traffic and weather information for display on the navigation system map (with active subscription, where available).
Global Positioning System (GPS) Antenna
The global positioning system (GPS) antenna is part of the multi-band antenna located on the roof of the vehicle. The GPS antenna is used to collect the signals of the orbiting GPS satellites. Within the antenna is housed a low noise amplifier that allows for a more broad and precise reception of this data. The GPS antenna amplifier is powered through the coaxial cable.
The antenna is connected to the human machine interface module through a signal splitter. The signal splitter is a component for dividing the navigation signal into two paths without any transmission loss. This allows the use of a single GPS antenna to provide a signal to both the human machine interface module and the telematics communication interface module.
Route Guidance
The map will display the route to the selected destination. Voice prompts alert the operator of upcoming events (turns) and arrivals at the destination. The navigation system will automatically recalculate if the route is not followed. The human machine interface module uses data received from the global positioning system (GPS) satellites, the vehicle speed signal. and serial data information to accurately display the current position of the vehicle.
Points of Interest
The map database provides point of interest information. Points of interests are locations that are frequently visited. Points of interest can be can be displayed on the map or set as a destination. The following are some of the available Points of interests:
* Gas Station
* Restaurant
* College
* Police Station
OnStar (R) (If equipped)
When OnStar is activated, a serial data message is sent to the radio that activates a software program. When the software begins its process, the fade goes to the front, Bass and Treble are set to the mid range, the outputs are mono, and the audio source is OnStar. OnStar takes priority over any other audio source. All of these actions are preset values stored in the radio.
For additional OnStar information, refer to OnStar Description and Operation OnStar.
Steering Wheel Controls (If equipped)
Some audio functions are available using the steering wheel controls. The steering wheel controls duplicate the function of the primary controls available on the radio.
For additional information on steering wheel controls, refer to Steering Wheel Controls Description and Operation Steering Wheel Controls.
Auto Volume Control
With auto volume control, the audio system will adjust automatically to make up for road and wind noise as you drive, by increasing the volume as vehicle speed increases. To use auto volume control, set the volume at the desired level, and then select either Low, Medium, or High. To turn auto volume control off, select the Off screen button.