P1682
DTC P1682
Diagnostic Instructions
* Perform the Diagnostic System Check - Vehicle prior to using this diagnostic procedure. Initial Inspection and Diagnostic Overview
* Strategy Based Diagnosis for an overview of the diagnostic approach.
* Diagnostic Procedure Instructions provide an overview of each diagnostic category.
DTC Descriptor
DTC P1682
- Ignition 1 Switch Circuit 2
Diagnostic Fault Information
Typical Scan Tool Data
Circuit/System Description
There are 2 ignition 1 voltage circuits supplied to the engine control module (ECM). The first ignition circuit is provided by the powertrain relay, through a fuse. This ignition 1 voltage circuit supplies power to all the internal ECM circuits associated with the throttle actuator control (TAC) operation. The second ignition 1 voltage circuit is supplied by the ignition switch through a fuse, and is used to power the remaining internal ECM circuits. If the ECM detects a voltage difference between the 2 ignition 1 voltage circuits, DTC P1682 will set.
Conditions for Running the DTC
* The ignition is ON.
* System voltage is more than 5.23 volts.
* The powertrain relay is commanded ON.
* DTC P1682 runs continuously.
Conditions for Setting the DTC
The ECM detects that the voltage level difference is greater than 3 volts between the 2 ignition 1 voltage circuits, for more than 3 seconds.
Action Taken When the DTC Sets
DTC P1682 is a Type B code.
Conditions for Clearing the DTC
DTC P1682 is a Type B code.
Diagnostic Aids
This test procedure requires that the vehicle battery has passed a load test and is completely charged. Refer to Battery Inspection/Test. Battery Inspection/Test
Circuit/System Verification
Important: On the scan tool, the powertrain relay is referred to as the EC ignition relay.
1. If DTCs P0685, P0689, or P0690 are set, diagnose those DTCs first.
2. Ignition ON, engine OFF, observe both the Ignition 1 Voltage signal and the EC Ignition Relay Feedback signal parameters on the scan tool. Both parameter values should display no more than 3 volts difference between the 2 parameters.
^ If the vehicle passes the Circuit/System Verification test, operate the vehicle within the Conditions for Running the DTC. You may also operate the vehicle within the conditions that are captured in the Freeze Frame/Failure Records data list.
Circuit/System Testing
Important: You must perform the Circuit/System Verification before proceeding with Circuit/System Testing.
Testing the Ignition 1 Signal Circuit
Important: A resistance of 5 ohms or greater in the circuit will cause the DTC to set.
1. Ignition ON, verify that B+ is available to both test points of the inline fuse from the ignition main relay to the ECM.
^ If B+ is only available on one test point of the fuse, test the ignition 1 voltage circuit from the fuse to the ECM for a short to ground. If the circuit tests normal, replace the ECM.
^ If B+ is not available on either test point of the fuse, replace the underhood fuse block.
2. Ignition OFF, disconnect the ECM C1 connector.
3. Ignition ON, verify that B+ is available at C1-19.
^ If B+ is not available, test the ignition 1 voltage circuit for an open/high resistance condition. If the circuit tests normal, replace the ECM.
4. If all circuits test normal, replace the ECM.
Testing the EC Ignition Relay Feedback Circuit
Important: A resistance of 5 ohms or greater in the circuit will cause the DTC to set.
1. Ignition OFF, remove the powertrain relay from the underhood fuse block.
2. Ignition ON, connect a 3A fused jumper wire from B+ to the powertrain ignition 1 voltage circuit terminal. Verify that the EC Ignition Relay Feedback parameter displays B+ on the scan tool.
^ If the scan tool parameter is less than the specified value, test the ignition 1 voltage circuit for an open/high resistance or short to ground. If the circuit tests normal, replace the ECM.
Repair Instructions
Perform the Diagnostic Repair Verification after completing the diagnostic procedure. Verification Tests
* Programming and Relearning Programming and Relearning
* Relay Replacement (Attached to Wire Harness) Relay Replacement (Within an Electrical Center)
* Junction Block Replacement - Accessory Wiring