B3265
DTC B3265
DTC Descriptors
DTC B3265 01
- Trunk Release Output Circuit Short to Battery
DTC B3265 06
- Trunk Release Output Circuit Short to Ground or Open
Diagnostic Fault Information
Important: Always perform the Diagnostic System Check - Vehicle prior to using this diagnostic procedure. Initial Inspection and Diagnostic Overview
Circuit/System Description
The body control module (BCM) provides a low side drive output that controls the trunk relay. The BCM monitors the voltage level on the trunk release relay control circuit to determine when a failure has occurred. The voltage level on this circuit should be high while the trunk relay is not energized, that is; the trunk release feature has not been activated. Voltage will be near 0 volts when the relay is energized. When the BCM receives a trunk release signal from a switch or keyless entry transmitter, it responds by applying ground to the trunk release relay control circuit, which energizes the trunk relay.
Conditions for Running the DTC
The ignition is ON.
Conditions for Setting the DTC
The following conditions exist for more than 1 second:
B3265 01
The BCM detects a short to battery in the trunk release relay control circuit when the output is active.
B3265 06
The BCM detects a short to ground or an open in the trunk release relay control circuit when the output is inactive.
Action Taken When the DTC Sets
The BCM disables the trunk release relay control until the next ignition cycle.
Conditions for Clearing the DTC
* The current DTC clears when the malfunction is no longer present.
* The history DTC will clear after 100 consecutive fault-free ignition cycles have occurred.
Diagnostic Aids
DTC B3265 06 will also set anytime the 10-amp TRUNK fuse is open. Besides a short to ground on the relay coil voltage supply circuit or the relay switch voltage supply circuit, a short to ground on the rear compartment lid release actuator output circuit can cause the fuse to open.
Circuit/System Verification
Ignition ON, press and hold the liftgate touch pad, observe the Liftgate Release Switch parameter in the scan tool. The scan tool Liftgate Release Switch parameter should display active momentarily. The trunk lid should release.
Circuit/System Testing
1. Ignition OFF, disconnect the trunk relay from the rear fuse block.
2. Ignition ON, verify that the rear compartment lid latch is deactivated.
• If the rear compartment lid latch is still activated, repair the relay switch control circuit (56) for a short to voltage.
3. Verify that a test lamp illuminates between the relay coil voltage supply circuit and ground.
• If the test lamp does not illuminate, repair the voltage supply circuit for a short to ground or an open/high resistance. If the voltage supply circuit fuse is open, test the relay switch control circuit (56) for a short to ground. If all circuit tests normal, test or replace the trunk relay.
4. Verify that a test lamp illuminates between the relay switch voltage supply circuit and ground.
• If the test lamp does not illuminate, repair the relay switch voltage supply circuit for a short to ground or an open/high resistance.
5. Disconnect the harness connector of the rear compartment lid latch.
6. Test for less than 1.0 ohm of resistance between the lid latch ground circuit and ground.
• If greater than 1.0 ohm, test the ground circuit for an open/high resistance.
7. Connect the harness connector of the rear compartment lid latch.
8. Connect a 3-amp fused jumper wire between the relay switch voltage supply circuit and the relay switch control circuit. Verify the rear compartment lid latch is activated
• If the rear compartment lid latch is not activated, test the relay switch control circuit for an open/high resistance. If the circuit tests normal, test or replace the rear compartment lid latch.
9. Connect a test lamp between the relay coil control circuit and the relay coil voltage supply circuit.
10. Press the liftgate touch pad switch. The test lamp should momentarily turn ON each time the solenoid is commanded ON.
• If the test lamp remains ON all the time, test for a short to ground on the relay coil control circuit. If the circuit tests normal, replace the BCM.
• If the test lamp remains OFF all the time, test for a short to voltage or an open/high resistance on the relay coil control circuit. If the circuit tests normal, replace the BCM.
11. If all circuits/connections test normal, replace the trunk relay.
Repair Instructions
Important: Always perform the Diagnostic Repair Verification after completing the diagnostic procedure. Verification Tests
* Relay Replacement (Attached to Wire Harness) Relay Replacement (Within an Electrical Center)
* Rear Compartment Lid Latch Replacement for sedan
* Liftgate Latch Replacement for extended sedan
* Control Module References for BCM replacement, setup, and programming. Programming and Relearning