P0815
DTC P0815, P0816, or P0826
Diagnostic Instructions
* Perform the Diagnostic System Check - Vehicle (Initial Inspection and Diagnostic Overview) prior to using this diagnostic procedure.
* Review Strategy Based Diagnosis (Initial Inspection and Diagnostic Overview) for an overview of the diagnostic approach.
* Diagnostic Procedure Instructions (Initial Inspection and Diagnostic Overview) provides an overview of each diagnostic category.
DTC Descriptors
DTC P0815
- Upshift Switch Circuit
DTC P0816
- Downshift Switch Circuit
DTC P0826
- Up and Down Shift Switch Circuit
Diagnostic Fault Information
Circuit/System Description
The transmission adaptive pressure (TAP) shift system allows the driver to manually shift gears by using the TAP shift switches located on the automatic transmission shifter. Pushing the Up switch will command an upshift and pushing the Down switch will command a downshift. Ignition voltage flows from the ignition 1 fuse through the TAP switch resistor array to the transmission control module (TCM). The TAP shift system is activated when the gear selector is in the manual (M) position. In the M range position, the TAP enable switch is closed and this activates the system by completing the TAP enable signal circuit from the body control module (BCM) to ground. TAP system is deactivated in all other range positions.
Conditions for Running the DTC
P0815 or P0816
* No DTC P0826.
* No DTCs P1825 or P1915.
* The engine speed is between 500-7,500 RPM for at least 5 seconds.
* The time since the last gear selector range change is greater than 6 seconds.
Conditions for Setting the DTC
P0815
The TCM detects a stuck ON upshift switch for 3 seconds in PARK, REVERSE, NEUTRAL, or D6- and for 600 seconds in PARK, REVERSE, NEUTRAL, D2, D4, OR D6.
P0816
The TCM detects a stuck ON downshift switch request for 3 seconds in PARK, REVERSE, NEUTRAL, or D6- and for 600 seconds in PARK, REVERSE, NEUTRAL, D2, D4, or D6.
P0826
The TCM detects an invalid voltage on the TAP up/down signal circuit for 8 seconds.
Action Taken When the DTC Sets
* DTCs P0815, P0816, and P0826 are Type C DTCs.
* The TCM disables TAP shift operation.
Conditions for Clearing the DTC
DTCs P0815, P0816, and P0826 are Type C DTCs.
Reference Information
Schematic Reference
Automatic Transmission Controls Schematics (Electrical Diagrams)
Connector End View Reference
* Electrical Center Identification Views
* Component Connector End Views (Connector Views)
* Splice Pack Connector End Views ([1][2]Branching Point)
* Inline Harness Connector End Views ([1][2]Diagrams)
Electrical Information Reference
* Circuit Testing (Component Tests and General Diagnostics)
* Connector Repairs (Component Tests and General Diagnostics)
* Testing for Intermittent Conditions and Poor Connections (Component Tests and General Diagnostics)
* Wiring Repairs (Component Tests and General Diagnostics)
Scan Tool Reference
* Scan Tool Output Controls (Scan Tool Output Controls)
* Scan Tool Data List (Scan Tool Data List)
* Scan Tool Data Definitions (Scan Tool Data Definitions)
DTC Type Reference
* Diagnostic Trouble Code (DTC) Type Definitions (Diagnostic Trouble Code Descriptions)
* Diagnostic Trouble Code (DTC) List/Type (Diagnostic Trouble Code Descriptions)
Circuit/System Verification
With the engine ON, engage the Tap Up and Tap Down switch positions while observing the Driver Shift Request scan tool parameter. The parameter should change to reflect the selected Up or Downshift switch position and with no Up or Downshift switch position selected the parameter should display None.
Circuit/System Testing
P0815
1. Select the Driver Shift Request parameter.
2. Disconnect the automatic transmission (AT) TAP shift switch connector.
• If the parameter status changes from Upshift to Invalid, replace the AT TAP shift switch.
• If the parameter status does not change, replace the control solenoid (w/body and TCM) valve assembly.
P0816
1. Select the Driver Shift Request parameter.
2. Disconnect the AT TAP shift switch connector.
• If the parameter status changes from Downshift to Invalid, replace the AT TAP shift switch.
• If the parameter status does not change, replace the control solenoid (w/body and TCM) valve assembly.
P0826
1. Inspect the fuse in the ignition 1 voltage circuit for an open.
• If the fuse is open, test the ignition 1 and the tap up and tap down circuit for a short to ground.
• If the fuse is OK, test the ignition 1 and the tap up and tap down signal circuit for an open or short to voltage.
2. Test the AT TAP shift switch for correct resistance value, 8.11-8.39 ohm.
• If the resistance is not within specifications, replace the switch assembly.
• If the resistance is within specifications, replace the control solenoid (w/body and TCM) valve assembly.
Repair Instructions
Perform the Diagnostic Repair Verification (Verification Tests) after completing the diagnostic procedure.
* Replace the AT TAP shift switch - refer to Automatic Transmission Manual Shift Auxiliary Position Switch Replacement (Automatic Transmission Manual Shift Auxiliary Position Switch Replacement) .
* Replace the control solenoid (w/body and TCM) valve assembly - refer to Control Module References (Programming and Relearning) for replacement, setup, and programming.