P0336
DTC P0336
Diagnostic Instructions
* Perform the Diagnostic System Check - Vehicle (Initial Inspection and Diagnostic Overview) prior to using this diagnostic procedure.
* Review Strategy Based Diagnosis (Initial Inspection and Diagnostic Overview) for an overview of the diagnostic approach.
* Diagnostic Procedure Instructions (Initial Inspection and Diagnostic Overview) provides an overview of each diagnostic category.
DTC Descriptor
DTC P0336
- Crankshaft Position (CKP) Sensor Performance
Diagnostic Fault Information
Circuit/System Description
The crankshaft position (CKP) sensor circuits consist of an engine control module (ECM) supplied 5-volt reference circuit, low reference circuit and an output signal circuit. The CKP sensor is an internally magnetic biased digital output integrated circuit sensing device. The sensor detects magnetic flux changes of the teeth and slots of a 58-tooth reluctor wheel on the crankshaft. Each tooth on the reluctor wheel is spaced at 60-tooth spacing, with 2 missing teeth for the reference gap. The CKP sensor produces an ON/OFF DC voltage of varying frequency, with 58 output pulses per crankshaft revolution. The frequency of the CKP sensor output depends on the velocity of the crankshaft. The CKP sensor sends a digital signal, which represents an image of the crankshaft reluctor wheel, to the ECM as each tooth on the wheel rotates past the CKP sensor. The ECM uses each CKP signal pulse to determine crankshaft speed and decodes the crankshaft reluctor wheel reference gap to identify crankshaft position. This information is then used to determine the optimum ignition and injection points of the engine. The ECM also uses CKP sensor output information to determine the camshaft relative position to the crankshaft, to control camshaft phasing, and to detect cylinder misfire.
Conditions for Running the DTC
* DTCs P0340, P0341, P0345, P0346, P0365, P0366, P0380, P0381, P0641 or P0651 are not set.
* The engine is cranking or running.
* The DTC runs continuously when the above conditions are met.
Conditions for Setting the DTC
Important: The ECM detects engine movement by sensing the airflow through the mass air flow (MAF) sensor is more than 3 g/s, or by sensing CMP sensor pulses.
* The ECM detects that the engine is running, but receives less than 51 or more than 65 CKP sensor pulses each engine revolution for 8 of 10 engine revolutions.
* The ECM detects that the engine is running, but more than 19 resyncs occur within 25 seconds.
* The ECM detects that the engine has been running, but the crankshaft does not sync for 0.4 second.
Action Taken When the DTC Sets
* DTC P0336 is a Type B DTC.
* The CMP actuator is commanded to the Home or Parked position.
* The ignition system defaults to a limp home mode. The CMP sensor is used to determine engine position.
Conditions for Clearing the MIL/DTC
DTC P0336 is a Type B DTC.
Reference Information
Schematic Reference
Engine Controls Schematics (Electrical Diagrams)
Description and Operation
Electronic Ignition System Description (Electronic Ignition System Description)
Electrical Information Reference
* Circuit Testing (Component Tests and General Diagnostics)
* Connector Repairs (Component Tests and General Diagnostics)
* Wiring Repairs (Component Tests and General Diagnostics)
DTC Type Reference
Powertrain Diagnostic Trouble Code (DTC) Type Definitions (Diagnostic Trouble Code Descriptions)
Scan Tool Reference
Control Module References (Programming and Relearning) for scan tool information
Circuit/System Verification
1. If DTC P0335 is also set, diagnose P0335 first.
2. With the ignition OFF, inspect the engine wiring harnesses carrying the CMP sensor circuits for the following conditions:
* Close routing of secondary ignition wires
* Close routing of aftermarket electrical equipment
* Close to solenoids, motors, and relays
• Correct any wire harness routing or component placement conditions if it is determined to be a possible source of electrical interference.
3. Start the engine. Using the Live Plot function on the scan tool, select the CMP parameter. Change the minimum spec to 400 RPM and the maximum spec to 4,000 RPM. Select the CKP sensor parameter. Change the minimum spec to 600 RPM and the maximum spec to 3,300 RPM.
4. Observe the scan tool.
5. Quickly accelerate and release the accelerator pedal several times. Do not exceed 3,200 RPM. The graphed lines on the Live Plot display should track together across the screen.
• If the vehicle passes the Circuit/System Verification Test, operate the vehicle within the Conditions for Running the DTC. You may also operate the vehicle within the conditions that are captured in the Freeze Frame/Failure Records Data List.
Circuit/System Testing
1. Ignition OFF, inspect the CKP sensor for looseness and correct installation.
• If the sensor is loose, inspect the sensor and the O-ring for damage. Replace as necessary.
2. Inspect the engine for the following conditions:
* Engine oil for debris and contamination
* Crankshaft reluctor wheel for damage
* The timing chain, tensioner, and sprockets for wear or damage
• If debris is found in the engine oil, inspect the internal engine components to determine the cause. Repair or replace any worn or damaged components. Refer to Camshaft Timing Drive Components Cleaning and Inspection () and Crankshaft and Bearing Cleaning and Inspection (Overhaul).
Component Test
1. Inspect the CKP sensor for looseness and correct installation. Remove the CKP sensor from the engine and inspect the sensor and the O-ring for damage.
• If the sensor is loose, incorrectly installed, or damaged, repair or replace the CKP sensor.
2. Connect the CKP sensor connector to the CKP sensor. Turn ON the ignition, with the engine OFF.
3. Observe the CKP Active Counter parameter on the scan tool. Pass a steel object by the tip of the sensor repeatedly. The CKP Active Counter parameter should increment.
• If the parameter does not increment, replace the CKP sensor.
Repair Instructions
Perform the Diagnostic Repair Verification (Verification Tests) after completing the diagnostic procedure.
Crankshaft Position Sensor Replacement (Service and Repair)