Engine Electrical
DTC P0562
Diagnostic Instructions
* Perform the Diagnostic System Check - Vehicle (Initial Inspection and Diagnostic Overview) prior to using this diagnostic procedure.
* Review Strategy Based Diagnosis (Initial Inspection and Diagnostic Overview) for an overview of the diagnostic approach.
* Diagnostic Procedure Instructions (Initial Inspection and Diagnostic Overview)provides an overview of each diagnostic category.
DTC Descriptor
DTC P0562
- System Voltage Low - ECM
Diagnostic Fault Information
Typical Scan Tool Data
Circuit/System Description
The engine control module (ECM) monitors the system voltage to ensure that the voltage stays within the proper range. Damage to components, and incorrect data may occur if the voltage is out of range. If the ECM detects that the system voltage is too low, then DTC P0562 sets.
Conditions for Running the DTC
The engine is running.
Conditions for Setting the DTC
The ECM detects that the system voltage is less than 9 volts for 5 seconds.
Action Taken When the DTC Sets
DTC P0562 is a type C DTC.
Conditions for Clearing the DTC
DTC P0562 is a type C DTC.
Diagnostic Aids
A low voltage DTC in multiple modules indicates a concern in the charging system.
Reference Information
Schematic Reference
* Engine Controls Schematics (LAT) (Electrical Diagrams)Engine Controls Schematics (LE5) (Electrical Diagrams)for the 2.4L (LAT/LE5) engines
* Engine Controls Schematics for the 3.5L (LZ4) engine
* Engine Controls Schematics (Electrical Diagrams)for the 3.6L (LY7) engine
Connector End View Reference
Component Connector End Views (Connector Views)
Description and Operation
Charging System Description and Operation (Description and Operation)
Electrical Information Reference
* Circuit Testing (Component Tests and General Diagnostics)
* Connector Repairs (Component Tests and General Diagnostics)
* Testing for Intermittent Conditions and Poor Connections (Component Tests and General Diagnostics)
* Wiring Repairs (Component Tests and General Diagnostics)
DTC Type Reference
Powertrain Diagnostic Trouble Code (DTC) Type Definitions (Diagnostic Trouble Code Descriptions)
Scan Tool Reference
Control Module References (Programming and Relearning)for scan tool information
Circuit/System Verification
1. Engine running, accessories OFF, measure and record the battery voltage at the battery terminals. The voltage should be between 12.6 and 15.0 volts.
• If not within the specified range, refer to Charging System Test (Charging System Test).
2. Observe the scan tool ECM Ignition 1 Signal parameter. The reading should be between 12.6 and 15.0 volts.
Circuit/System Testing
1. Ignition OFF, disconnect the harness connectors at the ECM.
2. Ignition OFF and scan tool disconnected, open and close the driver door, and wait 1 minute. Test for less than 5 ohms between the appropriate ground circuit terminal listed below and ground.
* Terminal 73 X1 (LZ4)
* Terminal 73 X2 (LAT, LE5, LY7)
• If greater than the specified range, test the ground circuit for an open/high resistance.
3. Verify that a test lamp illuminates between the B+ circuit terminal 20 X1 and ground.
• If the test lamp does not illuminate, test the B+ circuit for a short to ground or an open/high resistance.
4. Install a 3A jumper wire between the appropriate PWR/TRN relay control circuit terminal listed below and ground.
* Terminal 13 X1 (LE5)
* Terminal 40 X1 (LAT, LY7)
* Terminal 59 X1 (LZ4)
5. Ignition ON, verify that a test lamp illuminates between the ignition circuit terminals listed below and ground.
* Terminal 3 X1 (LE5)
* Terminal 18 X1 (LAT, LY7, LZ4)
* Terminal 19 X1 (all engines)
* Terminal 47 X1 (LZ4)
* Terminal 73 X1 (LE5)
* Terminal 13 X2 (LAT, LY7)
6. If all circuits test normal, replace the ECM.
Repair Instructions
Perform the Diagnostic Repair Verification (Verification Tests) after completing the diagnostic procedure.
Control Module References (Programming and Relearning)for ECM replacement, setup, and programming.