P0615
DTC P0615
Diagnostic Instructions
* Perform the Diagnostic System Check - Vehicle (Diagnostic System Check - Vehicle) prior to using this diagnostic procedure.
* Review Strategy Based Diagnosis (Strategy Based Diagnosis) for an overview of the diagnostic approach.
* Diagnostic Procedure Instructions (Diagnostic Procedure Instructions) provides an overview of each diagnostic category.
DTC Descriptor
DTC P0615
- Starter Relay Control Circuit
Diagnostic Fault Information
Typical Scan Tool Data
Circuit/System Description
When the ignition switch is placed in the START position, a discrete signal is supplied to the body control module (BCM) notifying it that the ignition is in the START position. The BCM then sends a serial data message to the engine control module (ECM) that crank has been requested. The ECM then verifies that the transmission is in Park or Neutral. If it is, the ECM then supplies 12 V to the control circuit of the CRNK relay. When this occurs, battery voltage is supplied through the switch of the CRNK relay to terminal A X2 of the starter solenoid. The ECM monitors the voltage on the starter relay control circuit. If the voltage is not what is expected, then DTC P0615 sets.
Conditions for Running the DTC
* The ignition is in the START position.
* The system voltage is between 9.5-18 V.
Conditions for Setting the DTC
The ECM detects improper voltage on the control circuit of the CRNK relay.
Action Taken When the DTC Sets
DTC P0615 is a type C DTC.
Conditions for Clearing the DTC
DTC P0615 is a type C DTC.
Reference Information
Schematic Reference
Starting and Charging Schematics (Electrical Diagrams)
Connector End View Reference
Component Connector End Views (Connector End Views By Name)
Description and Operation
Starting System Description and Operation (Description and Operation)
Electrical Information Reference
* Circuit Testing (Circuit Testing)
* Connector Repairs (Connector Repairs)
* Testing for Intermittent Conditions and Poor Connections (Testing for Intermittent Conditions and Poor Connections)
* Wiring Repairs (Wiring Repairs)
DTC Type Reference
Powertrain Diagnostic Trouble Code (DTC) Type Definitions (Powertrain Diagnostic Trouble Code (DTC) Type Definitions)
Scan Tool Reference
Control Module References (Programming and Relearning) for scan tool information
Circuit/System Verification
Attempt to start the engine while observing the following ECM scan tool control circuit status parameters.
* Starter Relay Ckt Short Gnd Test Status
* Starter Relay Ckt Open Test Status
* Starter Relay Ckt Short Volts Test Status
Each parameter should toggle between OK and Not Run or Not Run and OK.
Circuit/System Testing
1. Ignition OFF, disconnect the CRNK relay.
2. Ignition OFF and scan tool disconnected, open and close the driver door, and wait 1 minute. Test for less than 5 Ohms between the ground circuit terminal 85 and ground.
• If greater than the specified range, test the ground circuit for an open/high resistance.
3. Connect a test lamp between the control circuit terminal 86 and the ground circuit terminal 85.
4. Transmission in park, turn the ignition switch between the OFF and START positions. The test lamp should turn ON and OFF when changing between the positions.
• If the test lamp is always ON, test the control circuit for short to voltage. If the circuit tests normal, replace the ECM.
• If the test lamp is always OFF, test the control circuit for a short to ground or an open/high resistance. If the circuit tests normal, replace the ECM.
5. If all circuits test normal, test or replace the CRNK relay.
Component Testing
Relay Test
1. Ignition OFF, disconnect the CRNK relay.
2. Test for 60-180 Ohms between terminals 85 and 86.
• If not within the specified range, replace the relay.
3. Test for infinite resistance between the following terminals:
* 30 and 86
* 30 and 87
* 30 and 85
* 85 and 87
• If not the specified value, replace the relay.
4. Install a 20 A fused jumper wire between relay terminal 85 and 12 V. Install a jumper wire between relay terminal 86 and ground. Test for less than 2 Ohms between terminals 30 and 87.
• If greater than specified range, replace the relay.
Repair Instructions
Perform the Diagnostic Repair Verification (Verification Tests) after completing the diagnostic procedure.
* Relay Replacement (Relay Replacement (Within an Electrical Center))
* Control Module References (Programming and Relearning) for ECM replacement, setup, and programming.