B0081

DTC B0081

Diagnostic Instructions

* Perform the Diagnostic System Check - Vehicle (Diagnostic System Check - Vehicle) prior to using this diagnostic procedure.
* Review Strategy Based Diagnosis (Strategy Based Diagnosis) for an overview of the diagnostic approach.
* Diagnostic Procedure Instructions (Diagnostic Procedure Instructions) provides and overview of each diagnostic category.

DTC Descriptors
DTC B0081 3A
- Passenger Presence System Incorrect Component Installed

DTC B0081 39
- Passenger Presence System Internal Electronic Failure

DTC B0081 71
- Passenger Presence System Invalid Serial Data Received

Circuit/System Description

When the ignition is turned ON, the inflatable restraint sensing and diagnostic module (SDM) performs tests to diagnose critical malfunctions within itself. When the SDM has completed the power-up mode, the SDM will establish communication with the passenger presence system (PPS) module. The PPS module will respond by illuminating both of the PASSENGER AIR BAG ON/OFF indicators ON. The SDM will then transmit a request message to the PPS module to receive the PPS module verification ID. The PPS module will transmit the verification ID to the SDM, and the SDM will compare the ID received to data stored in memory. If the data stored in memory does not match the information transmitted by the PPS module or the SDM detects that the PPS module has set a current DTC the SDM will then disable the instrument panel (I/P) module deployment loop, set DTC B0081 and illuminate the AIR BAG indicator.

Conditions for Running the DTC

Ignition voltage is between 9-16 volts.

Conditions for Setting the DTC

All of the following conditions must exist for 5 seconds:

B0081 3A
* The SDM has received an ID message from the PPS which does not match the ID stored in the SDM memory.
* The SDM has reset the PPS module twice without detecting the correct ID message.

B0081 39
* The SDM has received a Not OK message from the PPS.
* The SDM has not received a message from the PPS.

B0081 71

The SDM has received invalid serial data from the PPS.

Action Taken When the DTC Sets

* The SDM requests the instrument panel cluster (IPC) to illuminate the AIR BAG indicator.
* The I/P module deployment loop will be disabled.

Conditions for Clearing the DTC

* The condition for setting the DTC no longer exists.
* A history DTC will clear once 100 malfunction-free ignition cycles have occurred.

Diagnostic Aids

If either the SDM or PPS module was replaced, verify that the correct part number was used for the vehicle application as this can cause DTC B0081 to set.

Reference Information
Schematic Reference

SIR Schematics ([1][2]Air Bag Systems)
Connector End View Reference

Component Connector End Views (Connector End Views By Name)
Description and Operation

SIR System Description and Operation (SIR System)
Electrical Information Reference

* Circuit Testing (Circuit Testing)
* Connector Repairs (Connector Repairs)
* Testing for Intermittent Conditions and Poor Connections (Testing for Intermittent Conditions and Poor Connections)
* Wiring Repairs (Wiring Repairs)

Scan Tool Reference

Control Module References (Programming and Relearning) for scan tool information

Circuit/System Verification

Note: When removing connectors inspect for damage or corrosion. Damage or corrosion in the following requires repair or replacement of the affected.

* PPS module
* PPS module wiring harness
* SDM
* SDM wiring harness

1. Verify that DTC B0081 39 is not set.

• If the DTC is set, replace the PPS module.

2. Verify the correct SDM and PPS module part number are installed for the vehicle configuration.

• If incorrect SDM or PPS module are installed, replace with the correct module.

3. Verify that no PPS DTCs are present. Refer to Passenger Presence System Displaying Code Procedure (Component Tests and General Diagnostics).

• If PPS DTC's are present, refer to Diagnostic Trouble Code (DTC) List - Vehicle (Diagnostic Trouble Code (DTC) List - Vehicle) for the appropriate DTC diagnostic procedure.

4. Ignition ON, verify the appropriate inflatable restraint passenger air bag ON/OFF indicator illuminates.

• If the appropriate inflatable restraint passenger air bag ON/OFF indicator does not illuminate, refer to Passenger Presence System Indicator Circuit Malfunction (Passenger Presence System Indicator Circuit Malfunction).

5. Verify that DTC B0081 is not set as current.

• If DTC is set as current, replace the PPS module.

Repair Instructions

Perform the Diagnostic Repair Verification (Verification Tests) after completing the diagnostic procedure.

Control Module References (Programming and Relearning) for SDM and PPS module replacement, setup, and programming