Seat Belt Indicator Circuit Malfunction - Passenger
Seat Belt Indicator Circuit Malfunction - Passenger
Diagnostic Instructions
* Perform the Diagnostic System Check - Vehicle (Diagnostic System Check - Vehicle) prior to using this diagnostic procedure.
* Review Strategy Based Diagnosis (Strategy Based Diagnosis) for an overview of the diagnostic approach.
* Diagnostic Procedure Instructions (Diagnostic Procedure Instructions) provides an overview of each diagnostic category.
Diagnostic Fault Information
Circuit/System Description
When an individual is sitting in the passenger seat the passenger presence sensor detects the individual. A signal to the SDM indicates a person is in the passenger seat. The SDM will turn the passenger seat belt indicator on. The passenger seat belt switch is a 2-wire switch wired to the inflatable restraint sensing and diagnostic module (SDM) using a signal circuit and a low reference circuit. When the seat belt is unbuckled the switch is closed, and when the seat belt is buckled the switch is open. The SDM sends the status of the passenger seat belt via a hard wire to the passenger air bag disable switch. After receiving the message, the passenger air bag disable switch controls the illumination of the passenger seat belt indicator.
Reference Information
Schematic Reference
Seat Belt Schematics ([1][2]Electrical Diagrams)
Connector End View Reference
Component Connector End Views (Connector End Views By Name)
Description and Operation
Seat Belt System Description and Operation (Description and Operation)
Electrical Information Reference
* Circuit Testing (Circuit Testing)
* Connector Repairs (Connector Repairs)
* Testing for Intermittent Conditions and Poor Connections (Testing For Intermittent Conditions and Poor Connections)
* Wiring Repairs (Wiring Repairs)
Scan Tool Reference
Control Module References (Programming and Relearning) for scan tool information
Circuit/System Verification
1. Ignition ON, have someone sit in the passenger seat. With a scan tool verify the Automatic Occupant Sensing Current Front Occupancy Status indicates Occupied.
• If the scan tool does not indicate Occupied, test the passenger presence sensor signal circuit and the low reference circuit for an open or short. If the circuits test normal, replace the passenger presence sensor. Refer to Front Seat Cushion Cover and Pad Replacement (Front Seat Cushion Cover and Pad Replacement).
2. Ignition ON, with a scan tool perform the Passenger Seat Belt Reminder Indicator On/Off Control Function and verify the passenger seat belt indicator turns on and off.
• If the indicator is always ON or always OFF, refer to Seat Belt Indicator Malfunction.
3. With the scan tool monitor the Passenger Seat Belt Status parameter while buckling and unbuckling the seat belt. The parameter should display Buckled and Unbuckled when buckling and unbuckling the seat belt.
• If the values do not change, refer to Seat Belt Switch Malfunction.
Circuit/System Testing
Seat Belt Switch Malfunction
Note: When removing connectors inspect for damage or corrosion. Damage or corrosion in the following requires repair or replacement of the affected component/connector.
* B88 Seat belt switch
* Seat belt switch harness connector
* K36 SDM
* SDM harness connector
1. Ignition OFF, disconnect the harness connector at the B88 passenger seat belt switch.
2. Ignition OFF, test for less than 1 ohm between the low reference circuit terminal B and ground.
• If greater than the specified range, test the low reference circuit for an open/high resistance. If the circuit tests normal, replace the K36 SDM.
3. Ignition ON, verify the scan tool Passenger Seat Belt Status parameter displays Buckled.
• If not the specified value, test the signal circuit for a short to ground. If the circuit tests normal replace the K36 SDM.
4. Install a 3 A fused jumper wire between the signal circuit terminal A and the low reference circuit terminal B. Verify the scan tool Passenger Seat Belt Status parameter displays Unbuckled.
• If not the specified value, test the signal circuit for a short to voltage or an open/high resistance. If the circuit tests normal, replace the K36 SDM.
5. If all circuits test normal, replace the B88 seat belt switch.
Seat Belt Indicator Malfunction
1. Ignition OFF, disconnect the harness connector at the P14 passenger air bag disable indicator.
2. Test for less than 1 ohm between the ground circuit terminal 2 and ground.
• If greater than the specified range, test the ground circuit for an open/high resistance.
3. Connect a test lamp between the control circuit terminal 5 and ground.
4. Ignition ON, command the Passenger Seat Belt Reminder Indicator ON and OFF with a scan tool, the test lamp should turn ON and OFF while changing between the commanded states.
• If the test lamp is always ON, test the control circuit for a short to voltage. If the circuit tests normal, replace the K36 SDM.
• If the test lamp is always OFF, test the control circuit for a short to ground or an open/high resistance. If the circuit tests normal, replace the K36 SDM.
5. If all circuit test normal, test or replace the P14 passenger air bag disable indicator.
Component Testing
1. Ignition OFF, disconnect the harness connector at the B88 seat belt switch.
2. Test for infinite resistance between the signal circuit terminal A and the low reference terminal B, at the switch, with the switch in the open position.
• If less than the specified value, replace the B88 seat belt switch
3. Test for less than 1 ohm between the signal circuit terminal A and the low reference terminal B, at the switch, with the switch in the closed position.
• If greater than the specified range, replace the B88 seat belt switch.
Repair Instructions
Perform the Diagnostic Repair Verification (Verification Tests) after completing the diagnostic procedure.
* Driver or Passenger Seat Belt Buckle Replacement (Driver or Passenger Seat Belt Buckle Replacement)
* Inflatable Restraint Instrument Panel Module Indicator Replacement (Service and Repair)
* Control Module References (Programming and Relearning) for SDM and instrument panel cluster replacement, setup, and programming.